Baumatic dishwasher error codes

Many people consider Baumatic dishwashers rather reliable. However machines of even the most reliable brands can need repair every now and then. When something goes wrong, do not call a repair service at once: it may well happen that you can do the troubleshooting on your own using the list of Baumatic dishwasher error codes below.
To begin with, find the code in the first column. Having done this, you will be able to check the symptom as well as the cause of Baumatic dishwasher problems. After that it’s time to turn to the last column and try the suggested solutions for Baumatic dishwasher error codes.
Baumatic basic dishwasher error codes
Baumatic MG series dishwasher error codes



Baumatic basic dishwasher error codes

The Baumatic brand, which belongs to Candy Group since 2013, manufactures a wide range of basic dishwashers. There are both compact and standard sized models, integrated and free-standing versions. They can accommodate from 9 up to 16 place settings. Typically, they share the same system of error codes that are used to diagnose malfunctions.

CODESYMPTOMCAUSEWHAT TO DO
Err1LONGER FILL TIME.FAUCET IS NOT OPENEDEnsure that inlet hose is not kinked or crushed.
Err2LONGER or EXTENDED DRAINING TIMETHE DRAIN PIPE WAS PLACED
TOO HIGH WHEN IT WAS
INSTALLED.
Err3LONGER HEATING TIME – NOT
REACHING REQUIRED TEMPERATURE
MALFUNCTION OF
TEMPERATURE SENSOR OR OF
HEATING ELEMENT.
Err4OVERFILLEDTOO MUCH INLET WATER.
*NOTE * - THERE ARE
NUMEROUS CAUSES OF AN
‘Err4’ MESSAGE. REFER TO
APPLIANCE USAGE SECTION
OF THIS MANUAL FOR
GUIDELINES ON HOW TO
PREVENT AN OVERFILL.
Overdosing. 3-in-1 put in
with salt and/or rinse aid in the appliance =overdose.
Could also be a Water
Pressure problem.
Err6OPEN CIRCUITTHERMISTOR.CALL FOR A QUALIFIED SERVICE TECHNICIAN
Err7SHORT CIRCUITTHERMISTOR.CALL FOR A QUALIFIED SERVICE TECHNICIAN

Baumatic MG series dishwasher error codes

One of the most popular dishwasher from the Baumatic MG series is the MG5. The model called Dance Partner has a stylish colorful design. There are several programs with wash temperatures ranging from 40°C to 60°C. Some of the useful features include a half load function, turbo drying, electronic aqua stop, and a delay timer.

Failure CodeConditionCheck/Repair
E1 Longer than expected fill time.- Check the water pressure of your mains water supply.
- Clean the mesh filter that sits in the inlet hose.
- Ensure that the inlet hose is not kinked or crushed.
- Make sure the water tap that the machine is connected to is turned
on fully.
E2Longer or extended drain time.- The drain pipe may be placed in too high a position or incorrectly.
Check the installation instructions and ensure that the installation is
correct.
- Check that the outlet hose is not kinked or crushed.
- beyond its original
length.
E3Longer heating time- not reaching the required temperature.- Malfunction of the temperature sensor or heating element.
- Call Baumatic Service Department.
E4The machine has sensed water in the base- Check that the outlet hose is not kinked or crushed.
- Check that there are no blockages in the drain hose or the drainage
system that the appliance is connected to.
- The drain pipe may be placed in too high a position or incorrectly.
Check the installation instructions and ensure that the installation is
correct.
- Oversudsing being caused by a 3 in 1 detergent tablet being used
with separate salt and/or rinse aid.
E5Switch cannot shut off automatically- program not finishing its
cycle
- Low voltage or power switch failure.
- Call Baumatic Service Department.
E6Open circuit- Thermistor
- Call Baumatic Service Department.
E7Short circuit- Thermistor
- Call Baumatic Service Department.