Siemens dishwasher error codes

FaultCauseRemedial action
Error code E:22 is lit.Filters 29 are soiled or blocked.Clean filters. (See Cleaning and maintenance)
Error code E:24 is lit.Waste water hose is blocked or kinked.Install hose without kinks, remove any residue.
Siphon connection still sealed.Check connection to siphon and open if required.
Cover on the waste water pump loose.Lock cover correctly. (See Waste water pump)
Error code E:25 is lit.Waste water pump blocked or cover on the waste water pump is not locked in position.Clean pump and lock cover correctly. (See Waste water pump)
Error code E:27 is lit.Mains voltage too low.Not an appliance fault, have the mains voltage and electrical installation checked.
A different error code is indicated on the digital display. (E:01 to E:30)A technical fault has probably occurred.Switch off appliances with the ON/OFF switch 1I. After a short time restart the appliance.
If the problem recurs, turn off the tap and pull out the mains plug. Call customer service and mention the error code.
Display flashesDoor not closed properly.Close the door. Ensure that no objects (utensil, fragrance dispenser) are protruding over the basket and preventing the door from closing.
Refill indicator for salt 5 and/or rinse-aid 6 is lit.No rinse aid.Refill rinse aid.
No salt.Refill with special salt.
Sensor does not detect salt tablets.Use different special salt.
Refill indicator for salt 5 and/or rinse-aid 6 is not lit.Refill indicator switched off.Activation/deactivation (see chapter Water softening system/Special salt or Rinse aid).
There is still enough special salt/ rinse aid available.Check refill indicator, levels.

Siemens SN55M531TI Dishwasher Error Codes

FaultCauseRemedial action
"Check water supplyā€¯ display 3 lights up.Supply hose kinked.Install supply hose without kinks.
Tap turned off.Turn on the tap.
Tap jammed or calcified.Turn on the tap.
Flow rate must be min. 10 l/min. when water supply is open.
Filter in the water supply blocked.Switch off the appliance and pull out the mains plug. Turn off the tap. Unscrew water connection.
Error code E:22 is lit.Filters 27 are soiled or blocked.Clean filters. (See Cleaning and maintenance)
Error code E:24 is lit.Waste water hose is blocked or kinked.Install hose without kinks, remove any residue.
Siphon connection still sealed.Check connection to siphon and open if required.
Cover on the waste water pump loose.Lock cover correctly. (See Waste water pump)
Error code E:25 is lit.Waste water pump blocked or cover on the waste water pump is not locked in position.Clean pump and lock cover correctly. (See Waste water pump)
Error code E:27 is lit.Mains voltage too low.Not an appliance fault, have the mains voltage and electrical installation checked.
A different error code is indicated on the digital display. (E:01 to E:30)A technical fault has probably occurred.Switch off appliances with the ON/OFF switch 1 1 I. After a short time restart the appliance.
If the problem recurs, turn off the tap and pull out the mains plug.
Call customer service and mention the error code.
Display flashesDoor not closed properly.Close the door. Ensure that no objects (utensil, fragrance dispenser) are protruding over the basket and preventing the door from closing.
Refill indicator for salt 4 and/or rinse-aid 5 is lit.No rinse aid.Refill rinse aid.
No salt.Refill with special salt.
Sensor does not detect salt tablets.Use different special salt.
Refill indicator for salt 4 and/or rinse-aid 5 is not lit.Refill indicator switched off.Activation/deactivation (see chapter Water softening system/Special salt or Rinse aid).
There is still enough special salt/ rinse aid available.Check refill indicator, levels.
Water is left in the appliance at the end of the programme.Filter system or area under the filters 1271 is blocked.Clean filters and area underneath (see Waste water pump).
The programme has not yet ended.Wait until programme ends or reset (see Terminating the programme).