Caple washing machine error codes

Caple WMF1020 washing machine error codes

SAFETY MECHANISMSFAULTSACTIONS
FILLING (F01)EV activated for 8 min. and without water (except in the programme)The machine stops with the door lock activated
DOOR OPEN (F04)- Washing machines with instant opening door lock:IN USER PROGRAMME STOP (Programme end)
At the beginning of the programme the circuit detects that the door is not closed
Washing machines with PTC door lock:
If the door lock is without power for 8 seconds the fault is displayed
EMPTYING (F02)EB ON 6 min. and PN ON (full)STOP (Programme end)
OVERFULL (F07)The fault is displayed:
If the pressure switch detects that the washing machine is too full
If the pump connector is broken or is not connected
NTC (F05)NTC in short circuit or open circuitThe programme ends without heating the water
DOES NOT HEAT (F06)li < 5?C/15 min. (Except in reliability program)
MOTOR (F08)Tachogenerator failure, motor blockedSTOP (Programme end)
- The wash programme is stopped for 120 secondsDoor lock always activated
- The error counter starts counting
- If the error counter counts 3 faults the error code F08 is displayed
- When the stop time is exceeded the programme begins again
If the error does not occur in the next 20 seconds the error counter is reset. The programme stops (in any instance) and starts again in the same position. If the error occurs in the spin phase the programme will start the whole spin sequence again from the start.
This error returns to the initial conditions if the error is reset.
MOTOR INVERSION FAULT (F09)The drum rotation direction does not change until the motor stops (max. time 2 min.)
INTERNAL DOMOTIC FAULT (F10)Communication between the micro and the bus failsIn V1 nothing happens
In V3 and V4 the u@” symbol will flash intermittently
EXTERNAL DOMOTIC FAULT (F11)While communicating with the washing machine it is detected that a node is absentIn V1 nothing happens
In versions V3 and V4 the symbol and the lock symbol
will flash intermittently
BMF BUS FAULT (F12)While communicating with a washing machine a BMF fault is detected. In order to detect it, the followingIn version V1 nothing happens
must happen:In versions V3 and V4 the washing machine stops
- Display board: If the board does not receive the correct message (can be checked in the BMF variable "SinTraficoEnBus==1")(Programme end)
from the power board for more than 10 seconds, or if it is continually receiving LINK messages but not data
(no status messages. (Can be checked in the BMF by its meaning *TramaDatosATratar==0-') for more than 10
seconds, the fault F12 will be displayed.
- Power board: If the power board is continually sending LINK messages to the display board for more than 10 seconds (the master can recognise and check the BMF variable “EtadoLinkNodos"), the F12 fault is then displayed and should be activated in the master. If the power board receives a correct message from the display board (Link_Response or Data) the F12 fault is reset
IMBALANCE (C03)If an imbalance is detected when it makes 18 attempts to spin or during 15 minutes of attemptsThe washing machine spins at the lowest speed

Caple WMi1012 washing machine error codes

Error codeProblem
ENDDoor not closed properly. Close it.
E1Aquastop. Contact the nearest Service Centre after disconnecting the machine from the electrical power supply and closing the water tap.
E5No water for washing. See point 2 on the troubleshooting table.
E6The water does not drain. See point 4 on the troubleshooting table.

Caple WMi2003 washing machine error codes

CODESCAUSESSOLUTIONS
ErrlDoor is not properly shut.Shut the door properly, and then press the Start/Pause buttor
Err2Drainage error, water not emptied within 6 minutes.Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel.
Err3Temperature sensor not properly connected or damaged.Contact the maintenance personnel.
Err4Heater error (Appears at the end of a cycle).Contact the maintenance personnel.
Err5Water level not met in 8 minutes.Make sure that tap is turned on, and water pressure is normal. If problem still exists, please contact the maintenance personnel.
The height of the drain hose is below 80 cm. The drain hose is in water.Install drain hose within 80-100 cm of height.
Make sure the drain hose is not in water.
Err 7Motor error.Contact the maintenance personnel.
Err8Water exceeds protective level.Contact the maintenance personnel.
ErlOThe signal of Water level sensor is wrong.Contact the maintenance personnel.
EuArThe PCB and the motor cant't communicate.Contact the maintenance personnel.
EndEnd of wash cycle.
UNbWashing machine has an unbalanced load protection function.When unbalanced weight is greater than allowable maximum,the washing machine will not spin and will run at a speed to avoid abnormal vibration and noise1 .In case washing 1 piece of laundrytcorpet, bed sheet,table sheet,ect) make it symmetrical inside the drum.
2.Lower the wet weight of laundry pieces by wringing manually and placing them back in the drum in symmetrical position.
3.Take out and then reposition the laundry inside the washing machine in a more balanced position on the inner wall of the drum.
4.Add 1 or 2 pieces of laundry into the durm to reduce the unbalanced load effects.
5.Restort the spin cycle by selecting the spin program. In cose the failure persists, please contact o qualified technician to repair it