Samsung dryer error codes

Samsung dryers, in most cases, offer good value for money and have a variety of innovative features. Yet, when the appliance dies, you forget about all the advantages and have only one question: “How can I bring it back to life?”
Typically, Samsung dryers use a system of error codes. This means that in case of a malfunction the appliance shows a certain code depending on the type of problem. This helps a user to diagnose the washer and fix it. Want to know what an error code means? Refer to the table below.

Samsung DC68-02312A-04 dryer error codes

Code SymbolMeaningSolution
Sz'dHeater temperature control problem.Call for service.
dfDoor open sensing problem.
doDoor open error. When the door is open, the dryer will not operate.Be sure the door is latched shut. If problem continues, call for service.

Samsung DV9 Series dryer error codes

ERROR DISPLAYMEANINGSOLUTION
tEAir temperature sensor errorClean the filter case or heat exchanger filter. If the problem continues call for service.
tE5Compressor temperature sensor errorTurn the power on after 2-3 minutes and start again from the beginning.
dERunning the dryer with door openClose the door and then restart. If the problem continues call for service.
HECompressor overheatCall for service
2EIt occurs when low voltage is detected.Check if the power cord is plugged in. If the problem continues, please contact the service center.
5EThe water tank is full of water. The drain pump is out of order.Empty the water tank, turn the power on again and start again from the beginning. If the problem continues call for service.

Samsung DV9K60 series dryer error codes

CodeMeaningSolution
tcAir temperature sensor check.Clean the filter case or heat exchanger filter. If the problem continues call for service.
tC5Compressor temperature sensor check.Turn the power on after 2-3 minutes and start again from the beginning.
dCRunning the dryer with door open.Close the door and then restart. If the problem continues call for service.
HCCompressor overheat.Call for service.
9C2It occurs when low voltage is detected.Check if the power cord is plugged in. If the problem continues, please contact the service center.
5CThe water tank is full of water. The drain pump is out of order.Empty the water tank, turn the power on again and start again from the beginning. If the problem continues call for service.

Samsung DV48H7400E(G) dryer error codes

ERROR DISPLAYMEANINGSOLUTION
tETemperature sensor problem.Restart the cycle. If the code reappears, call for service.
HEInvalid heating Temp in running the dryer).Call for service.
dERunning the dryer with door open.Close the door and then restart. If the problem continues, call for service.
FEInvalid power source Frequency.Try restarting the cycle. If the problem continues, call for service.
9E1Electronic Control Problem (Over Voltage Error).Call for service.
AEElectronic Control Problem (Communication Error).Call for service.
E3Invalid state of Eeprom Communication.Call for service.
dFInvalid door.Call for service.
bE, bE2Unit detects a button is being pressed for over 30secs or button is stuck.Make sure a button is NOT being pressed continuously. Try restarting the cycle. If the problem continues, call for service.

Samsung DV48J7700E(G) series dryer error codes

NoCodeAction
1dCOperating the dryer with the door open.
• Make sure the door is properly closed.
• Make sure laundry is not caught in the door.
2FCInvalid power source frequency
• Check if you are using regular power source frequencies.
• Check the power frequency sensor circuit.
• Try restarting the cycle.
• If the information code remains, contact a customer service centre.
3ACElectronic control problem (Invalid Communication).
• First check the PCB and wire harness.
• If the information code remains, contact a customer service centre.
43CMalfunction is detected in the motor relay circuit.
• Check the motor connection cable.
• Check the motor relay operation of the PCB.
• Check the drum belt.
5bC2Incorrect button state.
• If the display PCB key circuit is shorted or not.
6HCHigh temperature heating check
• Clean the filter case or condenser.
7HC4• If the information code remains, contact a customer service centre.(enter the line test mode).
89C1The electronic control needs to be checked (Over Voltage Error).
• Check the PCB and wire harness.
• Check if power is supplied properly.
• If the information code remains, contact a customer service centre.
9tcThe Thermistor 1 resistance is very low or high.
• Check for a clogged lint screen
• Check if the vent system is restricted or.
• Check Thermistorl resistance.
10tC5The Thermistor2 resistance is very low or high.
• Check for a clogged lint screen.
• Check if the vent system is restricted.
• Check Thermistor2 resistance.

Samsung DV50K7500E Series dryer error codes

CodeAction
DCOperating the dryer with the door open.
• Make sure the door is properly closed.
• Make sure laundry is not caught in the door.
FCInvalid power source frequency
• Try restarting the cycle.
• If this information code remains, contact a Samsung service center.
ACElectronic control problem (Invalid Communication). • Contact a Samsung service center.
HCHigh temperature heating check
• Clean the lint filter.
• If this information code remains, contact a Samsung service center.
9C1The electronic control needs to be checked.
• Check if power is supplied properly.
• If the information code remains, contact a Samsung service center.
tcThe Thermistor 1 resistance is very low or high.
• Check for a clogged lint screen
• Check if the vent system is restricted.
• If this information code remains, contact a Samsung service center.
tC5The Thermistor2 resistance is very low or high.
• Check for a clogged lint screen.
• Check if the vent system is restricted.
• If this information code remains, contact a Samsung service center.
dFIncorrect door switch.
• Contact a Samsung service center.

Samsung DV56H9100E Series dryer error codes

ERROR DISPLAYMEANINGSOLUTION
tEThe thermistor resistance is very low or high.Clean the screen or vent. If the problem continues, call for service.
HEInvalid heating Temp when the dryer is running.Call for service.
dERunning the dryer with door open.Close the door and then restart. If the problem continues, call for service.
FEInvalid power source frequency.Try restarting the cycle. If the problem continues, call for service.
9E1Electronic Control Problem. (Over Voltage Error)Call for service.
AEElectronic Control Problem. (Communication Error)Call for service.
EEEInvalid state of Eeprom Communication.Call for service.
dFInvalid door.Call for service.
bE2Unit detects a button is being pressed for over 30secs or button is stuck.Make sure a button is NOT being pressed continuously. Try restarting the cycle. If the problem continues, call for service.

Samsung DV407AG series dryer error codes

ERROR DISPLAYMEANINGSOLUTION
ts, tOClogged Lint Screen. Vent is restricted Clean the screen or vent. If the problem continues call for service.
dORunning the dryer with door openClose the door and then restart. If the problem continues call for service.
dFDoor is not closing properlyCall for sen/ice.
bEButton stuck for more than 75 secsMake sure a button is NOT being pressed continuously. Try restarting the cycle. If the problem continues, call for service.
oDInvalid Dry timeCall for sen/ice.
hEInvalid heating Temp when running the dryerCall for sen/ice.
EtEEPROM is not communicating properlyTry restarting the cycle. If the problem continues call for service.
FEInvalid power source FrequencyTry restarting the cycle. If the problem continues call for service.

Samsung SDC17709 dryer error codes

ERROR DISPLAYMEANINGSOLUTION
tE2, tE4Clogged filter case is restricted.Clean the filter case or condenser. If the problem continues call for service.
dERunning the dryer with door openClose the door and then restart. If the problem continues call for service.
dFDoor is not closing properlyCall for service.
bEButton stuck for more than 30 secsMake sure a button is NOT being pressedcontinuously. Try restarting the cycle. If the problem continues, call for service.
hEClogged filter case is restricted. Invalid heating Temp when running the dryer.Clean the filter case or condenser. If the problem continues call for service
EtEEPROM is not communicating properlyTry restarting the cycle.If the problem continues call for service.
3EThe motor does not work properly.Try restarting the cycle.If the problem continues call for service.
5EThe water tank is full of water. The drain pump is out of order.Empty the water tank and start again. If the problem continues call for service.