Electrolux represents one of the trademarks of the concern that was established in the 1919 and gave the name to the transnational corporation. It belongs to hundred biggest firms of the planet.
Its impeccable quality exits for many decades and remains the main part of the success of the Electrolux production. Electrolux washer error codes are a part of its program of the quality maintenance.
The system of Electrolux washer error codes allows accurately revealing malfunctions and doing repairs.
Electrolux basic washer error codes
Electrolux EWFM series, AWF series washer error codes
Electrolux W series washer error codes
Electrolux IQ-Touch Wave-Touch EIFLW series washer error codes
Electrolux EWM series washer error codes
Electrolux ENV series washer error codes
Electrolux EIFLW55HIW – 27 Front-Load Washer error codes
Electrolux EWM2100 washer error codes
Electrolux PW9 washer error codes

Electrolux basic washer error codes

One of the world’s leaders in household appliances, Electrolux manufactures a diverse range of washing machines. Electrolux basic washers are reliable and efficient, while the newer models offer a number of advanced options, like Fast Wash, LuxCare, and Perfect Steam.

Code	Problem	Possible Cause	Remedy
Fault code E10 appears. The display RINSE + flashes	No water flows	Water tap is closed.	Open the water tap.
		Filter in screw connection of the inlet hose is blocked.	Close the water tap. Unscrew the hose from the tap, remove the filter and clean under running water
		Water tap is blocked with limescale or is faulty	Check the water tap and have it repaired if necessary.
The fault code E20 (error solution e20)appears. The RINSE display flashes.	The washing is not sufficiently spun. Water is left in the drum.	Drain hose is kinked.	Remove the kink.
		Maximum pump head (discharge height 1m from the appliance's base) is exceeded.	Contact your local Service Force Centre. For pumping heights over 1m a conversion kit is available as a special accessory.
		Drain pump is blocked.	Switch off the appliance and pull out the mains plug. Clean the drain pump
The fault code E40 appears. The display MAIN WASH flashes		The door is not correctly closed.	Close the door correctly. Start the programme again.

Electrolux EWFM series, AWF series washer error codes

Electrolux EWFM is a series of front-loading washing machines with low water, energy and detergent consumption. A drying board and an extractable shelf are some of their characteristic features. The Electrolux AWF range encompasses reliable front loaders with all the basic features, as well as several more upgraded options, like SuperQuick and AquaCare.

Code	Cause	Solutions
E10	The water tap is closed.	Open the water tap.
	The inlet hose is squashed or kinked.	Check the inlet hose connection.
	The filter in the inlet hose is blocked.	Clean the water inlet hose filter.
E20	The drain hose is squashed or kinked.	Check the drain hose connection.
	The drain filter is clogged.	Clean the drain filter.
E40	The door has not been closed.	Close the door firmly.
	The door is not properly closed	Close firmly the door

Electrolux W series washer error codes

Electrolux W is a really extensive and diverse line of washing machines. From the EWB series front loaders to the top-loading washers like EDI, these are reliable and economic appliances varying in washing and safety options, as well as capacity.

Code	Solution
Error code E05 or E06	When the error code E05 or E06 is displayed,this can be due to the motorbeing too hot.Stop the dryer and wait for 5 minutes. Start again and choose a program.If this does not help and the error code reappears the inspector of thelaundry must be contacted
Error code E12	When the error code is displayed this can be due to the user having over-filled the dryer with clothes that are too wet.Remove some of the clothes, close the door, and press the start button.If this does not help and the error code reappears the inspector of thelaundry must be contacted
Error code E14	When the ignition control fails to detect a flame, a signal is sent to the PCB, and error code E14 is displayed. When this condition occurs, the gas valve is shut off and the ignition control must be reset manually. Resetting Open the operating panel and press the gas reset button A on the back of the PCB for one second. OPL: Press the reset button B next to the operating panel. NOTE! When resetting the system the dryer must operate on a program with heat and the heat indicator must be on. Japan only: By opening and closing the door (coin operated dryers only).
Error code E15	When the error code is displayed this can be due to the user having overfilled the dryer. Remove some of the clothes, close the door, and press the start button. If this does not help and the error code reappears the inspector of the laundry must be contacted.
Error code E16	The error code is displayed if the user presses the start button while the vacuum switch is already closed. Resetting by opening / closing the door and pressing start button.

Electrolux IQ-Touch Wave-Touch EIFLW series washer error codes

Front-load washers from the EIFLW series are equipped with the IQ-Touch control panel, which shows you all the details of the washing program you have chosen. This series includes washing machines with a Touch-2-open cycle selector, a dispenser drawer, and a door latch with safety lock.

Error Code	Fault Condition	Check	Correction
E11	Fill time too long.	1. Is the incoming water flow normal?	Yes. Go to step (4). No. Go to step (2)
		2. Are the incoming water faucets turned on?	No. Turn water faucets on. Yes. Go to step (3).
		3. Is the incoming water pressure above (20) psi.	No. Have customer correct pressure problem. Yes. Check for kinked or blocked incoming water hoses, clean the incoming water screens. If problem still remains, replace the water inlet valve assembly.
		4. Does the fill water continue to enter the washer?	Yes. Go to step (5). No. Go to step (6)
		5. Remove power from the washer. Did the water fill stop?	Yes. Go to step (6) No. Replace the inlet valve assembly. Pressure switch checks good. Go to step (7). Pressure switch checks bad. Replace the pressure switch.
		6. Replace the pressure sensor	If this did not correct the problem, go to step 7.
		7. Replace the main control board.
E13	Water leak in tub or air leak in air bell.	1. Is the washer leaking water?	Yes. Correct water leak. No. Go to step (2)
		2. Is there an air leak in the air bell system?	Yes. Correct the air leak problem. No. Go to step (3)
		3. Replace the pressure sensor	If this did not correct the problem, Go to step (4)
		4. Replace the main control board.
E21	Water not pumping out fast enough.	1. Check the drain hose for restrictions.	Restriction. Correct problem. No restriction. Go to step (2).
		2. Start the washer and check for 120 VAC at the drain pump.	Zero. Check the wiring. If wiring good, replace the main control board.120 VAC. Remove the pump and check for blockage. If blocked, remove the restriction, if not, replace the pump.
E31	Electronic pressure switch failure.	Inspect the wiring between the pressure main control board.	Defective wiring. Correct wiring.Good wiring. Replace the pressure sensor. If this does not correct the problem, replace the main control board.
E32	Pressure sensor calibration problem.
E35	Pressure sensor indicates water overfill.	1. Is the water level above 4.5 inches ?	Yes. Go to step (2). No. Go to step (4).
		2. Does water enter the washer continuously?	Yes. Go to step (3). No. Check Air Trap for clog, if not replace the main control board.
		3. Remove power from washer. Does the water stop coming in?	No. Replace the water valve assembly. Yes. Check wiring to valve assembly for shorts. If wiring is good, replace the main control board.
		4. Replace the pressure sensor switch. Did this correct the problem?	Yes. Problem solved. No. Replace the main control board
E38	Air trap clogged.
E41	Control board thinks the door switch is open.	1. Is the loading door closed?	No. Close the door. Yes. Go the step (2).
		2. Can you hear the lock attempt to close?	Yes. Check the door strike. If good, replace the door switch. No. Go the step (3)
		3. Check wire connection between door lock and main control board	If good, replace the door lock. If problem is not corrected, replace the main control board.
E42	Door lock device failure
E44	Door closed sensing failure.
E45	Line door sensing failure.
E46	Door command sense.
E49	Door incongruence between door line and door sense.
E52	Bad signal from tachogenerator.	1. Disconnect the plug from the drive motor and measure the resistance pins 4 & 5 in the motor.	If the reading is between 105 & 130 Ohms, replace the motor control board. If the meter reads other than between 105 & 130 Ohms, replace the motor.
E53	Low Voltage to Motor Control Board.	1. Check wiring between the main control board and motor control board.	If good , replace the motor control board.
E54	Over speed.	1. Remove belt from the motor and spin the motor pulley. Does the motor spin free?	No. Replace the motor. Yes. Go to step (2)
		2. Spin the tub pulley. Does the tub spin free?	No. Check the tub bearings. Yes. Go to step (3)
		3. Disconnect the plug from the drive motor and measure resistance between pins 4 & 5 in the motor.	If meter reads other than between 105 & 130 Ohms, replace the motor. If reading is between 105 & 130 Ohms, Go to step (4)
		4. Disconnect plug from the motor and measure the resistance of the windings (pin 1 to pin 2, pin 1 to pin 3, pin 2 to pin 3). All readings should be between 3 and 6 Ohms.	If the readings are correct, replace motor control board. If the readings are incorrect, replace motor.
E55	Under speed.
E57	High current on inverter	1. Find out if unit was overloaded. If not, remove belt from the motor and spin the motor pulley. Does the motor spin free?	No. Replace the motor. Yes. Go to step (2)
		2. Spin the tub pulley. Does the tub spin free?	No. Check the tub bearings. Yes. Go to step (3)
		3. Disconnect plug from the motor and measure resistance of the windings (pin 1 to pin 2, pin 1 to pin 3, pin 2 to pin 3). All readings should be between 3 and 6 Ohms.	If readings are correct, check wiring from motor to motor control board, If good, replace motor control board. If the readings are incorrect, replace motor.
E58	High current on motor phase.
E59	No tachogenerator signal for 3 seconds.	See E54	See E54
E5A	High temperature on heat sink caused by overloading.	See E57	See E57
E5C	High Voltage experienced by MC.	1. Have power company check the frequency and voltage of the incoming power.	If correct, for error code E5C, replace motor control board. If correct, for error codes EA1, EA2, EA3, EAE or EA5, replace main control board
E5D	Communication problem.	1. Communication problem. Check the wiring between the main control board and the motor control board.	Wiring bad, correct wiring problem.Wiring good, replace main control board. If problem is not corrected,replace the motor control board.
E5E	Communication problem.
E5F	MC is continuously resetting.
E67	Heater sensing relay failure.	1. Check the resistance of the heating element. It should be approximately 14 ohms.	If readings are incorrect, replace heating element.
		2. Check the resistance between ground and both heater terminals. It should be open when heater terminals are disconnected.	If readings are incorrect, replace the heating element. If problem is not corrected, replace main control board.
E68	Current leakage to ground on heater or fuse opened.
E69	Heating element relay failure.
E71	Drum water NTC failure. (Tub heater)	1. Check the resistance of the drum water NTC. Is it around 4.8K ohms?	No, replace the heating element. Yes, check the wiring
E74	Wash temperature does not increase.	See E71	See E71
E91	Communication error between UI board and main control board.	1. Communication problem. Check wiring between the main control board and user interface board.	Wiring bad, Correct wiring problem. Wiring good, Replace the user interface board. If problem is not corrected, replace the main control board.
E92	User Interface to Main Board communications error	See E91
E93	Console or Main Board control problem.
E94	Main Board control problem.
E95	Communication problem between microprocessor and external EEPROM.
E97	Console or Main Board control problem.
E98	Console control problem.	See E5D	See E5D
E9F	Communication protocol
EA1	Power supply frequency out of limits	See E5C	See E5C
EA2	Power supply voltage too high
EA3	Power supply voltage too low
EA5	Main Voltage sensing failure
EAE	Line safe relay sensing failure
EF1	Clogged drain pump.	Unclog the drain pump
EF2	Too much soap.	Advise customer to reduce amount of soap being used.
EF5	Incorrect water temperature.	1. Are the hot and cold water hoses switched?	Yes. Switch the hoses to correct position No. go to step 2
		2. Is HOT water about the same temperature as the cold?	Yes. Fix the HOT water in the house supply.
EF8	Key Stuck	Check all buttons

Electrolux EWM series washer error codes

Appliances from the Electrolux EWM series are manufactured by the company’a Swedish division Distiparts based not far from Jönköping. Most of them are front loaders, yet top loading washing machines (like EWM 1000 AEG) can also be found within this range.

Alarm	Description	Possible fault	Action/Machine status	Reset
E11	Difficulty in filling during wash phase	Tap closed or water pressure insufficient; Drain hose incorrectly positioned; Water fill solenoid faulty; Leaks from pressure switch hydraulic circuit; Pressure switch faulty; Wiring faulty; Circuit board faulty.	Cycle paused, door closed	Start
E13	Water leakage	Drain hose incorrectly positioned; Water pressure insufficient; Water fill solenoid faulty; Leaks or blockage in pressure switch hydraulic circuit; Pressure switch faulty; Circuit board faulty.
E21	Difficulties in draining	Drain hose kinked/blocked/incorrectly positioned; Drain filter clogged or dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; Circuit board faulty; Current leakage from heating element to ground.	Cycle paused
E23	Drain pump triac faulty	Drain pump faulty; Wiring faulty; Circuit board faulty.	Safety drain - Cycle stopped, door open	Selector on “0”
E24	Problems with «sensing» of drain pump triac	Circuit board faulty.	Safety drain – Cycle stopped, door released
E33	Incongruence between contact closure of anti- boiling and 1st level of pressure switch	Pressure switch faulty; Current leakage from heating element to ground; Heating element; Wiring faulty; Circuit board faulty.	Safety drain - Cycle stopped, door open
E35	Water overflow	Water fill solenoid faulty; Leaks from pressure switch hydraulic circuit; Pressure switch faulty; Wiring faulty; Circuit board faulty.	Cycle blocked, door closed. Safety drain. Drain pump (sequence 5 min. ON - 5 min. OFF)
E36	«sensing» circuit of anti-boiling pressure switch faulty	Circuit board faulty.	Cycle blocked, door closed
E37	«sensing» circuit of 1st level faulty	Circuit board faulty.
E39	HV «sensing» circuit of anti-flooding pressure switch faulty	Circuit board faulty.
E41	Door open	Door safety interlock faulty; Wiring faulty; Circuit board faulty.	Cycle paused	Start
E42	Problems with aperture of door			Start or Selector on “0”
E43	Power triac on door interlock faulty		Safety drain, door released
E44	Door interlock «sensing» faulty	Circuit board faulty.
E45	«sensing» on door interlock triac faulty
E51	Motor power triac short-circuited	Circuit board faulty; Current leakage from motor or wiring.	Cycle blocked, door closed (after 5 attempts in diagnostics or immediate during selection)
E52	No signal from motor tachimetric generator	Motor faulty; Wiring faulty; Circuit board faulty.
E53	«sensing» circuit on motor triac faulty	Circuit board faulty.	Cycle blocked
E54	Motor relay contacts sticking	Circuit board faulty; Current leakage from motor or wiring.	Cycle blocked, door closed (after 5 attempts in diagnostics or immediate during selection)
E61	Insufficient heating during washing	NTC sensor faulty; Heating element faulty; Wiring faulty; Circuit board faulty.	Heating phase skipped
E62	Overheating during washing		Safety drain (with cooling water fill) - Stop with door open
E66	Power relay for heating element faulty	Circuit board faulty; Current leakage from heating element or wiring to ground.
E71	NTC washing sensor faulty	NTC sensor faulty; Wiring faulty; Circuit board faulty.	Heating phase skipped
E82	Error in reset position of selector	Circuit board faulty.	Cycle cancelled
E83	Error in reading selector position	Configuration data incorrect; Circuit board faulty.	During the cycle continues normally, switches off completely during selection
E93	Incorrect machine configuration		Appliance blocked
E94	Incorrect washing cycle configuration
E95	Communications error between microprocessor and EEPROM	Circuit board faulty.
E96	Incongruence between hardware version and configuration.	Configuration data incorrect; Circuit board faulty.
E97	Incongruence between programme selector and cycle configuration
EB1	Power supply frequency of appliance incorrect	Mains power supply problems (incorrect / interference); Circuit board faulty.	Cycle blocked until normal power supply conditions are restored
EB2	Voltage too high
EB3	Voltage too low

Electrolux ENV series washer error codes

ENV06 is among the most popular washers from the Electrolux ENV line. The front loader produced by the company’s Swedish division Distiparts uses the same platform as the EWM1000, EWM2000evo, and EWM3000ne washing machines. There are models with vertical and horizontal pushbuttons.

Alarm	Possible fault	Action/machine status	Reset
E11	Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty.	Cycle is paused with door locked.	START/RESET
E12
E13	Drain tube improperly positioned; Water pressure too low; Water fill solenoid valve is faulty; Water circuit on pressure switch is leaking/clogged; Pressure switch faulty.
E21	Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty; Electrical current leak between heating element and ground.	Cycle is paused (after 2 attempts).
E22		Cycle is paused
E23	Drain pump faulty; Wiring faulty; PCB faulty.	Safety drain cycle - Cycle stops with door unlocked.	RESET
E24	PCB faulty.
E31	Pressure switch; Wiring; Main PCB.	Cycle stops with door locked.
E32	Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Water circuit on pressure switch; pressure switch; Wiring; main board.	Cycle is paused.	START/RESET
E35	Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty.	Cycle stops. Safety drain cycle. Drain pump continues to operate (5 min. on, then 5 min. off, etc.).	RESET
E38	Water circuit on pressure switches; Pressure switches; Motor belt broken.	Heating phase is skipped.	START/RESET
E3A	PCB faulty.	Cycle stops with door locked.	RESET
E41	Door lock unit faulty; Wiring faulty; PCB faulty.	Cycle is paused.	START/RESET
E42
E43		(Safety drain cycle) Cycle stops.	ON/OFF RESET
E44	PCB faulty.
E45
E51	PCB faulty; current leakage from motor or from wiring.	Cycle blocked, door locked (after 5 attempts).	RESET
E52	Motor faulty; wiring faulty; PCB faulty.
E53	PCB faulty.	Cycle blocked, door locked
E54	PCB faulty; current leakage from motor or from wiring	Cycle blocked, door locked (after 5 attempts).
E57	Wiring defective on inverter for motor, inverter board defective.
E58	Wiring defective on inverter for motor, inverter board defective, abnormal motor operation (motor overloaded); Motor defective.
E59	Motor defective; Wiring defective on inverter for motor; Inverter board defective.
E5A	Inverter board defective. NTC open (on the inverter board). Overheating caused by continuous operation or ambient conditions (let appliance cool down).
E5H	Wiring defective, Inverter board defective.
E5C	Inverter board defective, the masters voltage is too high (measure the masters voltage).
E5d	Line interference, Wiring defective, defective main board or inverter board.		RESET
E5E	Defective wiring between main board and inverter board, Defective inverter board, defective main board.	Cycle stops	ON/OFF
E5F	Defective inverter board, Defective wiring, defective main board.	Cycle stops with door locked (after 5 attempts).	RESET
E61	NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty.	The heating phase is skipped.	START/RESET
E62		Safety drain cycle – Cycle stopped with door open.	RESET
E66	PCB faulty.
E68	Earth-leakage between heater and earth.	Cycle blocked with door open.
E69	Washing heating element interrupted (thermofuse open)		START/RESET
E71	Faulty NTC sensor; Wiring faulty; PCB faulty.	Heating is skipped.
E72	Wiring faulty; Drying NTC sensor (condenser) faulty; PCB faulty.	Drying heating is skipped
E73	Wiring faulty; Drying NTC sensor (duct) faulty; PCB faulty.
E74	NTC sensor improperly positioned; Faulty NTC sensor; Wiring faulty; PCB faulty.	Heating is skipped.
E82	PCB faulty (Wrong configuration data). Selector, wiring		RESET
E83		Cycle cancelled.	START/RESET
E91	Wiring faulty; Faulty control/display board PCB faulty.		RESET
E92	Wrong control/display board; Wrong PCB (do not correspond to the model).		OFF/ON START
E93	Incorrect configuration data; PCB faulty		OFF/ON
E94
E95	PCB faulty.		RESET
E97	Faulty PCB (Wrong configuration data).
E98	Incompatibility between main board and Inverter.		OFF/ON
E9b / E9H	Display board.		ON/OFF RESET
E9C
E9d
E9F	PCB.		OFF/ON
EH1	Power supply problems (incorrect / disturbance); PCB faulty.	Wait for frequency nominal conditions.
EH2		Wait for voltage nominal conditions.
EH3
EHE	Wiring faulty; PCB faulty.	Safety drain cycle – Cycle stopped with door open	RESET
EHF	PCB faulty.	Safety drain cycle – Cycle stopped with door open
EC1	Solenoid valve faulty/blocked; PCB faulty.	Cycle interrupted with door closed. Drain pump functions always (5 min., then it stops for 5 min. etc.)
EC3	Wiring faulty; Weight sensor faulty; PCB faulty.		START/RESET
Ed1	Wiring faulty between PCB and WD board; WD board faulty; PCB faulty.	Cycle interrupted.	OFF/ON
Ed2	Wiring faulty between PCB and WD thermostats; WD board faulty; PCB faulty.	Cycle interrupted with door open.	RESET
Ed3
Ed4	Wiring faulty: WD board faulty; PCB faulty.
EF1	Drain tube blocked/kinked/too high; Drain filter dirty/blocked.	Warning displayed at the end of cycle (specific LED).	START/RESET
EF2	Excessive detergent dosing; drain tube kinked/blocked; Drain filter dirty/blocked.	Warning displayed after 5 attempts or by the specific LED.	RESET
EF3	Water leaks onto base frame; water control system defective.	Machine drains and cycle stops	ON/OFF RESET
EF4	Tap closed, water pressure too low.		RESET
EF5	Final spin phases skipped.

Electrolux EIFLW55HIW – 27 Front-Load washer error codes

Error code	Fault condition
E11	Fill time too long.
E13	Water leak in tub or air leak in air bell.
E21	Water not pumpinq out fast enouqh.
E31	Electronic pressure switch failure.
E32	Pressure sensor calibration problem.
E35	Pressure sensor indicates water overfill.
E38	Air trap cloqqed.
E41	Control board thinks the door switch is open.
E42	Door lock device failure
E44	Door closed sensinq failure.
E45	Line door sensinq failure.
E46	Door command sense.
E49	Door incnqruence between door line and door sense.
E52	Bad siqnal from tacho qenerator.
E53	Low Voltaqe to Motor Control Board.
E54	Over speed.
E55	Under speed.
E57	High current on inverter.
E58	Hiqh current on motor phase.
E59	No tacho signal for 3 seconds.
E5A	Hioh temperature on heat sink caused bv overloadino.
E5C	Hiqh Voltaqe experienced by MC.
E5D	Communication problem.
E5E	Communication problem.
E5F	MC is continuously resettinq.
E67	Heater sensinq relav failure.
E68	Current leakaqe to qround on heater or fuse opened.
E69	Heatinq element relay failure.
E71	Drum water NTC failure. (Tub heater)
E74	Wash temperature does not increase.
E91	Communication error between Ul board and main control board.
E92	Ul MB communications error
E93	Console or Main Board control problem.
E94	Main Board control problem.
E95	Communication problem between microprocessor and external EEPROM.
E97	Console or Main Board control problem.
E98	Console control problem.
E9F	Communication protocol
EA1	Power supply frequency out of limits
EA2	Power supply voltage too high
EA3	Power supply voltage too low
EA5	Main Voltage sensing failure
EAE	Line safe relay sensinq failure
EF1	Cloqqed drain pump.
EF2	Too much soap.
EF5	Incorrect water temperature.
EF8	Key Stuck

Electrolux EWM2100 washer error codes

Alarm	Possible fault	Action/machine status
EOO	No alarm
E11	Difficulties in water fill for washing	Tap closed or water pressure too low; Drain tube improperly Dositioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty.
E12	Difficulties in water fill for drying
E13	Water leakage	Drain hose incorrectly positioned; mains pressure insufficient; water fill solenoid faulty; leakage/blockage of pressure switch hydraulic circuit; pressure switch faulty.
E21	Difficulties in draining for washing	Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty.
E22	Difficulties in draining for drying
E23	Drain pump triac faulty	Drain pump faulty; Wiring faulty; PCB faulty.
E24	Fault in “sensing” circuit of drain pump triac (wrong input signal to microprocessor)	PCB faulty.
E31	Electronic pressure switch circuit faulty (frequency of pressure switch signal out of limits)	Electronic pressure switch; Wiring; PCB faulty.
E32	Incorrect calibration of electronic pressure switch (The electronic pressure switch generates a signal with instable frequency during the drain phase)	Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty;
		Leaks from water circuit on pressure switch; Pressure switch; Wiring faulty; PCB faulty.
E35	Water overflow	Water fill solenoid faulty; Leaks from water circuit on pressure switch; ^ Dressure switch faulty; wiring faulty; PCB faulty.
E38	Pressure chamber blocked (water level does not vary for at least 30 sec. during drum rotation	Motor drive belt broken; Hydraulic circuit pressure switch clogged.
E3A	Heating elem. relay sensing faulty (input signal to microprocessor always 0V or 5V)	PCB faulty.
E41	Door open (after 15 sec.)	Door interlock faulty; wiring faulty; PCB faulty.
E42	Problems of door closure
E43	Interlock power supply triac faulty
E44	Door interlock sensing circuit triac faulty	PCB faulty.
E45	Door interlock sensing circuit triac faulty (wrong input signal to microprocessor)
E51	Motor power supply triac short- circuited	PCB faulty; current leakage from motor or from wiring.
E52	No signal from motor tachometric generator	Motor faulty; wiring faulty; PCB faulty.
E53	Motor triac sensing circuit faulty (input signal to microprocessor wrong)	PCB faulty.
E54	Motor relay contacts sticking (high voltage level when the relay changes to OFF)	PCB faulty; current leakage from motor or from wiring.
E61	Insufficient heating during washing	NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty.
E62	Overheating during washing (temperature higher than 88°C for a time higher than 5 min.)
E66	Heating element power relay faulty (incongruence between sensing and relay)	PCB faulty.
E68	Current dispersion to earth (value of mains voltage different from main value)	Current dispersion between between heating element and earth.
E69	Heating element interrupted	Wiring faulty; Heating element for washing interrupted (thermofuse open).
E71	Washing NTC sensor faulty (short- circuited or open)	Wiring faulty; Washing NTC sensor faulty; PCB faulty.
E72	Drying condenser NTC sensor faulty (voltage value out of limits, sensor short-circuited or open)	Wiring faulty; Drying NTC sensor (condenser) badly positioned or faulty; WD board faulty.
E73	Drying duct NTC sensor faulty (voltage value out of limits, sensor short-circuited or open)	Wiring faulty; Drying NTC sensor (duct) badly positioned or faulty; WD board faulty.
E74	Washing NTC sensor badly positioned
E82	Error in selector reset position	PCB faulty (Wrong configuration data).
E83	Error in selector reading

Electrolux PW9 washer error codes

Error code	Cause/Action
01E	Acknowledgement signal for water level not received within time allowed.
02 E	Door status acknowledgement signal not received during program operation.
03E	Door lock acknowledgement signal not received within time allowed.
07E	Water level above parameter set for safety, during program.
10E	Water level is above parameter set (10 scale units) after water discharge.