Electrolux washer error codes

Electrolux represents one of the trademarks of the concern that was established in the 1919 and gave the name to the transnational corporation. It belongs to hundred biggest firms of the planet.
Its impeccable quality exits for many decades and remains the main part of the success of the Electrolux production. Electrolux washer error codes are a part of its program of the quality maintenance.
The system of Electrolux washer error codes allows accurately revealing malfunctions and doing repairs.
Electrolux basic washer error codes
Electrolux EWFM series, AWF series washer error codes
Electrolux W series washer error codes
Electrolux IQ-Touch Wave-Touch EIFLW series washer error codes
Electrolux EWM series washer error codes
Electrolux ENV series washer error codes
Electrolux EIFLW55HIW – 27 Front-Load Washer error codes
Electrolux EWM2100 washer error codes
Electrolux PW9 washer error codes

Electrolux basic washer error codes

One of the world’s leaders in household appliances, Electrolux manufactures a diverse range of washing machines. Electrolux basic washers are reliable and efficient, while the newer models offer a number of advanced options, like Fast Wash, LuxCare, and Perfect Steam.

CodeProblemPossible CauseRemedy
Fault code E10 appears. The display RINSE + flashesNo water flowsWater tap is closed.Open the water tap.
Filter in screw connection of the inlet hose is blocked.Close the water tap. Unscrew the hose from the tap, remove the filter and clean under running water
Water tap is blocked with limescale or is faultyCheck the water tap and have it repaired if necessary.
The fault code E20 (error solution e20)appears. The RINSE display flashes.The washing is not sufficiently spun. Water is left in the drum.Drain hose is kinked.Remove the kink.
Maximum pump head (discharge height 1m from the appliance's base) is exceeded.Contact your local Service Force Centre. For pumping heights over 1m a conversion kit is available as a special accessory.
Drain pump is blocked.Switch off the appliance and pull out the mains plug. Clean the drain pump
The fault code E40 appears. The display MAIN WASH flashesThe door is not correctly closed. Close the door correctly. Start the programme again.

Electrolux EWFM series, AWF series washer error codes

Electrolux EWFM is a series of front-loading washing machines with low water, energy and detergent consumption. A drying board and an extractable shelf are some of their characteristic features. The Electrolux AWF range encompasses reliable front loaders with all the basic features, as well as several more upgraded options, like SuperQuick and AquaCare.

CodeCauseSolutions
E10The water tap is closed.
Open the water tap.
The inlet hose is squashed or kinked.Check the inlet hose connection.
The filter in the inlet hose is blocked.Clean the water inlet hose filter.
E20The drain hose is squashed or kinked.Check the drain hose connection.
The drain filter is clogged. Clean the drain filter.
E40The door has not been closed.Close the door firmly.
The door is not properly closedClose firmly the door

Electrolux W series washer error codes

Electrolux W is a really extensive and diverse line of washing machines. From the EWB series front loaders to the top-loading washers like EDI, these are reliable and economic appliances varying in washing and safety options, as well as capacity.

CodeSolution
Error code E05 or E06When the error code E05 or E06 is displayed,this can be due to the motorbeing too hot.Stop the dryer and wait for 5 minutes. Start again and choose a program.If this does not help and the error code reappears the inspector of thelaundry must be contacted
Error code E12When the error code is displayed this can be due to the user having over-filled the dryer with clothes that are too wet.Remove some of the clothes, close the door, and press the start button.If this does not help and the error code reappears the inspector of thelaundry must be contacted
Error code E14When the ignition control fails to detect a flame, a signal is sent to the PCB, and error code E14 is displayed.
When this condition occurs, the gas valve is shut off and the ignition control must be reset manually.
Resetting
Open the operating panel and press the gas reset button A on the back of the PCB for one second.
OPL: Press the reset button B next to the operating panel.
NOTE! When resetting the system the dryer must operate on a program with heat and the heat indicator must be on.
Japan only: By opening and closing the door (coin operated dryers only).
Error code E15When the error code is displayed this can be due to the user having overfilled the dryer.
Remove some of the clothes, close the door, and press the start button. If this does not help and the error code reappears the inspector of the laundry must be contacted.
Error code E16The error code is displayed if the user presses the start button while the vacuum switch is already closed.
Resetting by opening / closing the door and pressing start button.

Electrolux IQ-Touch Wave-Touch EIFLW series washer error codes

Front-load washers from the EIFLW series are equipped with the IQ-Touch control panel, which shows you all the details of the washing program you have chosen. This series includes washing machines with a Touch-2-open cycle selector, a dispenser drawer, and a door latch with safety lock.

Error CodeFault ConditionCheckCorrection
E11Fill time too long.1. Is the incoming water flow normal?Yes. Go to step (4).
No. Go to step (2)
2. Are the incoming water faucets turned on?No. Turn water faucets on.
Yes. Go to step (3).
3. Is the incoming water pressure above (20) psi.No. Have customer correct pressure problem. Yes. Check for kinked or blocked incoming water hoses, clean the incoming water screens. If problem still remains, replace the water inlet valve assembly.
4. Does the fill water continue to enter the washer?Yes. Go to step (5).
No. Go to step (6)
5. Remove power from the washer.
Did the water fill stop?
Yes. Go to step (6)
No. Replace the inlet valve assembly. Pressure switch checks good. Go to step (7). Pressure switch checks bad. Replace the pressure switch.
6. Replace the pressure sensorIf this did not correct the problem, go to step 7.
7. Replace the main control board.
E13Water leak in tub or air leak in air bell.1. Is the washer leaking water?Yes. Correct water leak.
No. Go to step (2)
2. Is there an air leak in the air bell system?Yes. Correct the air leak problem.
No. Go to step (3)
3. Replace the pressure sensorIf this did not correct the problem, Go to step (4)
4. Replace the main control board.
E21Water not pumping out fast enough.1. Check the drain hose for restrictions.Restriction. Correct problem.
No restriction. Go to step (2).
2. Start the washer and check for 120 VAC at
the drain pump.
Zero. Check the wiring. If wiring good, replace the main control board.120 VAC. Remove the pump and check for blockage. If blocked, remove the restriction, if not, replace the pump.
E31 Electronic pressure switch failure.Inspect the wiring between the pressure
main control board.
Defective wiring. Correct wiring.Good wiring. Replace the pressure sensor. If this does not correct the problem, replace the main control board.
E32Pressure sensor calibration problem.
E35Pressure sensor indicates water overfill.1. Is the water level above 4.5 inches ?Yes. Go to step (2).
No. Go to step (4).
2. Does water enter the washer continuously?Yes. Go to step (3).
No. Check Air Trap for clog, if not replace the main control board.
3. Remove power from washer.
Does the water stop coming in?
No. Replace the water valve assembly.
Yes. Check wiring to valve assembly for shorts. If
wiring is good, replace the main control board.
4. Replace the pressure sensor switch.
Did this correct the problem?
Yes. Problem solved.
No. Replace the main control board
E38Air trap clogged.
E41Control board thinks the door switch is open.1. Is the loading door closed?No. Close the door.
Yes. Go the step (2).
2. Can you hear the lock attempt to close?Yes. Check the door strike. If good, replace the door switch.
No. Go the step (3)
3. Check wire connection between door lock
and main control board
If good, replace the door lock. If problem is not corrected, replace the main control board.
E42Door lock device failure
E44Door closed sensing failure.
E45Line door sensing failure.
E46Door command sense.
E49Door incongruence between door line and door sense.
E52Bad signal from tachogenerator.1. Disconnect the plug from the drive motor and measure the resistance pins 4 & 5 in the motor.If the reading is between 105 & 130 Ohms, replace the motor control board. If the meter reads other than between 105 & 130 Ohms, replace the motor.
E53Low Voltage to Motor Control Board.1. Check wiring between the main control board and motor control board.If good , replace the motor control board.
E54Over speed.1. Remove belt from the motor and spin the motor pulley. Does the motor spin free?No. Replace the motor.
Yes. Go to step (2)
2. Spin the tub pulley. Does the tub spin free?
No. Check the tub bearings.
Yes. Go to step (3)
3. Disconnect the plug from the drive motor and measure resistance between pins 4 & 5 in the motor.If meter reads other than between 105 & 130 Ohms, replace the motor. If reading is between 105 & 130 Ohms, Go to step (4)
4. Disconnect plug from the motor and measure the resistance of the windings (pin 1 to pin 2, pin 1 to pin 3, pin 2 to pin 3). All readings should be between 3 and 6 Ohms.If the readings are correct, replace motor control board. If the readings are incorrect, replace motor.
E55Under speed.
E57High current on inverter1. Find out if unit was overloaded. If not, remove belt from the motor and spin the motor pulley. Does the motor spin free?No. Replace the motor.
Yes. Go to step (2)
2. Spin the tub pulley. Does the tub spin free?No. Check the tub bearings.
Yes. Go to step (3)
3. Disconnect plug from the motor and measure resistance of the windings (pin 1 to pin 2, pin 1 to pin 3, pin 2 to pin 3). All readings should be between 3 and 6 Ohms.If readings are correct, check wiring from motor to motor control board, If good, replace motor control board. If the readings are incorrect, replace motor.
E58High current on motor phase.
E59No tachogenerator signal for 3 seconds.See E54See E54
E5AHigh temperature on heat sink caused by overloading.See E57See E57
E5CHigh Voltage experienced by MC.1. Have power company check the frequency and voltage of the incoming power.If correct, for error code E5C, replace motor control board. If correct, for error codes EA1, EA2, EA3, EAE or EA5, replace main control board
E5DCommunication problem.1. Communication problem. Check the wiring between the main control board and the motor control board.Wiring bad, correct wiring problem.Wiring good, replace main control board. If problem is not corrected,replace the motor control board.
E5ECommunication problem.
E5F MC is continuously resetting.
E67Heater sensing relay failure.1. Check the resistance of the heating element. It should be approximately 14 ohms.If readings are incorrect, replace heating element.
2. Check the resistance between ground and both heater terminals. It should be open when heater terminals are disconnected.If readings are incorrect, replace the heating element. If problem is not corrected, replace main control board.
E68Current leakage to ground on heater or fuse opened.
E69Heating element relay failure.
E71Drum water NTC failure. (Tub heater)1. Check the resistance of the drum water NTC.
Is it around 4.8K ohms?
No, replace the heating element.
Yes, check the wiring
E74Wash temperature does not increase.See E71See E71
E91Communication error between UI board and main control board.1. Communication problem. Check wiring between the main control board and user interface board.Wiring bad, Correct wiring problem. Wiring good, Replace the user interface board. If problem is not corrected, replace the main control board.
E92 User Interface to Main Board communications errorSee E91
E93Console or Main Board control problem.
E94Main Board control problem.
E95Communication problem between microprocessor and external EEPROM.
E97Console or Main Board control problem.
E98Console control problem.See E5DSee E5D
E9FCommunication protocol
EA1Power supply frequency out of limitsSee E5CSee E5C
EA2Power supply voltage too high
EA3Power supply voltage too low
EA5Main Voltage sensing failure
EAELine safe relay sensing failure
EF1Clogged drain pump.Unclog the drain pump
EF2Too much soap.Advise customer to reduce amount of soap being used.
EF5Incorrect water temperature.1. Are the hot and cold water hoses switched?Yes. Switch the hoses to correct position
No. go to step 2
2. Is HOT water about the same temperature as the cold?Yes. Fix the HOT water in the house supply.
EF8Key StuckCheck all buttons

Electrolux EWM series washer error codes

Appliances from the Electrolux EWM series are manufactured by the company’a Swedish division Distiparts based not far from Jönköping. Most of them are front loaders, yet top loading washing machines (like EWM 1000 AEG) can also be found within this range.

Alarm DescriptionPossible fault Action/Machine status Reset
E11Difficulty in filling during wash phaseTap closed or water pressure insufficient; Drain hose incorrectly positioned; Water fill solenoid faulty; Leaks from pressure switch hydraulic circuit; Pressure switch faulty; Wiring faulty; Circuit board faulty. Cycle paused, door closed Start
E13Water leakage Drain hose incorrectly positioned; Water pressure insufficient; Water fill solenoid faulty; Leaks or blockage in pressure switch hydraulic circuit; Pressure switch faulty; Circuit board faulty.
E21Difficulties in draining Drain hose kinked/blocked/incorrectly positioned; Drain filter clogged or dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; Circuit board faulty; Current leakage from heating element to ground. Cycle paused
E23Drain pump triac faulty Drain pump faulty; Wiring faulty; Circuit board faulty. Safety drain - Cycle stopped, door open Selector on “0”
E24Problems with «sensing» of drain pump triac Circuit board faulty. Safety drain – Cycle stopped, door released
E33 Incongruence between contact closure of anti- boiling and 1st level of pressure switch Pressure switch faulty; Current leakage from heating element to ground; Heating element; Wiring faulty; Circuit board faulty.Safety drain - Cycle stopped, door open
E35Water overflow Water fill solenoid faulty; Leaks from pressure switch hydraulic circuit; Pressure switch faulty; Wiring faulty; Circuit board faulty. Cycle blocked, door closed. Safety drain. Drain pump (sequence 5 min. ON - 5 min. OFF)
E36«sensing» circuit of anti-boiling pressure switch faultyCircuit board faulty. Cycle blocked, door closed
E37«sensing» circuit of 1st level faultyCircuit board faulty.
E39HV «sensing» circuit of anti-flooding pressure switch faultyCircuit board faulty.
E41Door open Door safety interlock faulty; Wiring faulty; Circuit board faulty. Cycle paused Start
E42Problems with aperture of door Start or Selector on “0”
E43Power triac on door interlock faulty Safety drain, door released
E44Door interlock «sensing» faultyCircuit board faulty.
E45«sensing» on door interlock triac faulty
E51Motor power triac short-circuitedCircuit board faulty; Current leakage from motor or wiring. Cycle blocked, door closed (after 5 attempts in diagnostics or immediate during selection)
E52No signal from motor tachimetric generatorMotor faulty; Wiring faulty; Circuit board faulty.
E53«sensing» circuit on motor triac faulty Circuit board faulty. Cycle blocked
E54 Motor relay contacts sticking Circuit board faulty; Current leakage from motor or wiring. Cycle blocked, door closed (after 5 attempts in diagnostics or immediate during selection)
E61 Insufficient heating during washing NTC sensor faulty; Heating element faulty; Wiring faulty; Circuit board faulty. Heating phase skipped
E62Overheating during washing Safety drain (with cooling water fill) - Stop with door open
E66Power relay for heating element faulty Circuit board faulty; Current leakage from heating element or wiring to ground.
E71 NTC washing sensor faultyNTC sensor faulty; Wiring faulty; Circuit board faulty. Heating phase skipped
E82Error in reset position of selector Circuit board faulty. Cycle cancelled
E83Error in reading selector position Configuration data incorrect; Circuit board faulty. During the cycle continues normally, switches off completely during selection
E93Incorrect machine configuration Appliance blocked
E94Incorrect washing cycle configuration
E95Communications error between microprocessor and EEPROMCircuit board faulty.
E96Incongruence between hardware version and configuration. Configuration data incorrect; Circuit board faulty.
E97Incongruence between programme selector and cycle configuration
EB1Power supply frequency of appliance incorrect Mains power supply problems (incorrect / interference); Circuit board faulty.Cycle blocked until normal power supply conditions are restored
EB2Voltage too high
EB3Voltage too low

Electrolux ENV series washer error codes

ENV06 is among the most popular washers from the Electrolux ENV line. The front loader produced by the company’s Swedish division Distiparts uses the same platform as the EWM1000, EWM2000evo, and EWM3000ne washing machines. There are models with vertical and horizontal pushbuttons.

AlarmPossible fault Action/machine status Reset
E11Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty. Cycle is paused with door locked. START/RESET
E12
E13Drain tube improperly positioned; Water pressure too low; Water fill solenoid valve is faulty; Water circuit on pressure switch is leaking/clogged; Pressure switch faulty.
E21Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty; Electrical current leak between heating element and ground. Cycle is paused (after 2 attempts).
E22Cycle is paused
E23Drain pump faulty; Wiring faulty; PCB faulty. Safety drain cycle - Cycle stops with door unlocked. RESET
E24PCB faulty.
E31Pressure switch; Wiring; Main PCB. Cycle stops with door locked.
E32Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Water circuit on pressure switch; pressure switch; Wiring; main board. Cycle is paused. START/RESET
E35Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty.Cycle stops. Safety drain cycle. Drain pump continues to operate (5 min. on, then 5 min. off, etc.).RESET
E38Water circuit on pressure switches; Pressure switches; Motor belt broken. Heating phase is skipped. START/RESET
E3A PCB faulty. Cycle stops with door locked. RESET
E41Door lock unit faulty; Wiring faulty; PCB faulty.Cycle is paused. START/RESET
E42
E43(Safety drain cycle) Cycle stops.ON/OFF RESET
E44PCB faulty.
E45
E51PCB faulty; current leakage from motor or from wiring. Cycle blocked, door locked (after 5 attempts). RESET
E52Motor faulty; wiring faulty; PCB faulty.
E53PCB faulty. Cycle blocked, door locked
E54PCB faulty; current leakage from motor or from wiringCycle blocked, door locked (after 5 attempts).
E57Wiring defective on inverter for motor, inverter board defective.
E58Wiring defective on inverter for motor, inverter board defective, abnormal motor operation (motor overloaded); Motor defective.
E59Motor defective; Wiring defective on inverter for motor; Inverter board defective.
E5AInverter board defective. NTC open (on the inverter board). Overheating caused by continuous operation or ambient conditions (let appliance cool down).
E5HWiring defective, Inverter board defective.
E5CInverter board defective, the masters voltage is too high (measure the masters voltage).
E5dLine interference, Wiring defective, defective main board or inverter board. RESET
E5EDefective wiring between main board and inverter board, Defective inverter board, defective main board. Cycle stops ON/OFF
E5FDefective inverter board, Defective wiring, defective main board. Cycle stops with door locked (after 5 attempts). RESET
E61NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. The heating phase is skipped.START/RESET
E62Safety drain cycle – Cycle stopped with door open.RESET
E66 PCB faulty.
E68Earth-leakage between heater and earth.Cycle blocked with door open.
E69 Washing heating element interrupted (thermofuse open) START/RESET
E71Faulty NTC sensor; Wiring faulty; PCB faulty.Heating is skipped.
E72Wiring faulty; Drying NTC sensor (condenser) faulty; PCB faulty.Drying heating is skipped
E73Wiring faulty; Drying NTC sensor (duct) faulty; PCB faulty.
E74NTC sensor improperly positioned; Faulty NTC sensor; Wiring faulty; PCB faulty.Heating is skipped.
E82PCB faulty (Wrong configuration data). Selector, wiring RESET
E83Cycle cancelled. START/RESET
E91Wiring faulty; Faulty control/display board PCB faulty. RESET
E92Wrong control/display board; Wrong PCB (do not correspond to the model).OFF/ON START
E93Incorrect configuration data; PCB faultyOFF/ON
E94
E95PCB faulty.RESET
E97Faulty PCB (Wrong configuration data).
E98Incompatibility between main board and Inverter. OFF/ON
E9b / E9HDisplay board. ON/OFF RESET
E9C
E9d
E9F PCB.OFF/ON
EH1Power supply problems (incorrect / disturbance); PCB faulty. Wait for frequency nominal conditions.
EH2Wait for voltage nominal conditions.
EH3
EHE Wiring faulty; PCB faulty. Safety drain cycle – Cycle stopped with door openRESET
EHF PCB faulty. Safety drain cycle – Cycle stopped with door open
EC1Solenoid valve faulty/blocked; PCB faulty.Cycle interrupted with door closed. Drain pump functions always (5 min., then it stops for 5 min. etc.)
EC3Wiring faulty; Weight sensor faulty; PCB faulty. START/RESET
Ed1 Wiring faulty between PCB and WD board; WD board faulty; PCB faulty. Cycle interrupted. OFF/ON
Ed2Wiring faulty between PCB and WD thermostats; WD board faulty; PCB faulty.Cycle interrupted with door open.RESET
Ed3
Ed4Wiring faulty: WD board faulty; PCB faulty.
EF1Drain tube blocked/kinked/too high; Drain filter dirty/blocked. Warning displayed at the end of cycle (specific LED). START/RESET
EF2Excessive detergent dosing; drain tube kinked/blocked; Drain filter dirty/blocked. Warning displayed after 5 attempts or by the specific LED. RESET
EF3Water leaks onto base frame; water control system defective. Machine drains and cycle stopsON/OFF RESET
EF4Tap closed, water pressure too low. RESET
EF5Final spin phases skipped.

Electrolux EIFLW55HIW – 27 Front-Load washer error codes

Error codeFault condition
E11Fill time too long.
E13Water leak in tub or air leak in air bell.
E21Water not pumpinq out fast enouqh.
E31Electronic pressure switch failure.
E32Pressure sensor calibration problem.
E35Pressure sensor indicates water overfill.
E38Air trap cloqqed.
E41Control board thinks the door switch is open.
E42Door lock device failure
E44Door closed sensinq failure.
E45Line door sensinq failure.
E46Door command sense.
E49Door incnqruence between door line and door sense.
E52Bad siqnal from tacho qenerator.
E53Low Voltaqe to Motor Control Board.
E54Over speed.
E55Under speed.
E57High current on inverter.
E58Hiqh current on motor phase.
E59No tacho signal for 3 seconds.
E5AHioh temperature on heat sink caused bv overloadino.
E5CHiqh Voltaqe experienced by MC.
E5DCommunication problem.
E5ECommunication problem.
E5FMC is continuously resettinq.
E67Heater sensinq relav failure.
E68Current leakaqe to qround on heater or fuse opened.
E69Heatinq element relay failure.
E71Drum water NTC failure. (Tub heater)
E74Wash temperature does not increase.
E91Communication error between Ul board and main control board.
E92Ul MB communications error
E93Console or Main Board control problem.
E94Main Board control problem.
E95Communication problem between microprocessor and external EEPROM.
E97Console or Main Board control problem.
E98Console control problem.
E9FCommunication protocol
EA1Power supply frequency out of limits
EA2Power supply voltage too high
EA3Power supply voltage too low
EA5Main Voltage sensing failure
EAELine safe relay sensinq failure
EF1Cloqqed drain pump.
EF2Too much soap.
EF5Incorrect water temperature.
EF8Key Stuck

Electrolux EWM2100 washer error codes

AlarmPossible faultAction/machine status
EOONo alarm
E11Difficulties in water fill for washingTap closed or water pressure too low; Drain tube improperly Dositioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty.
E12Difficulties in water fill for drying
E13Water leakageDrain hose incorrectly positioned; mains pressure insufficient; water fill solenoid faulty; leakage/blockage of pressure switch hydraulic circuit; pressure switch faulty.
E21Difficulties in draining for washingDrain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty.
E22Difficulties in draining for drying
E23Drain pump triac faultyDrain pump faulty; Wiring faulty; PCB faulty.
E24Fault in “sensing” circuit of drain pump triac (wrong input signal to microprocessor)PCB faulty.
E31Electronic pressure switch circuit faulty (frequency of pressure switch signal out of limits)Electronic pressure switch; Wiring; PCB faulty.
E32Incorrect calibration of electronic pressure switch (The electronic pressure switch generates a signal with instable frequency during the drain phase)Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty;
Leaks from water circuit on pressure switch; Pressure switch; Wiring faulty; PCB faulty.
E35Water overflowWater fill solenoid faulty; Leaks from water circuit on pressure switch; ^ Dressure switch faulty; wiring faulty; PCB faulty.
E38Pressure chamber blocked (water level does not vary for at least 30 sec. during drum rotationMotor drive belt broken; Hydraulic circuit pressure switch clogged.
E3AHeating elem. relay sensing faulty (input signal to microprocessor always 0V or 5V)PCB faulty.
E41Door open (after 15 sec.)Door interlock faulty; wiring faulty; PCB faulty.
E42Problems of door closure
E43Interlock power supply triac faulty
E44Door interlock sensing circuit triac faultyPCB faulty.
E45Door interlock sensing circuit triac faulty (wrong input signal to microprocessor)
E51Motor power supply triac short- circuitedPCB faulty; current leakage from motor or from wiring.
E52No signal from motor tachometric generatorMotor faulty; wiring faulty; PCB faulty.
E53Motor triac sensing circuit faulty (input signal to microprocessor wrong)PCB faulty.
E54Motor relay contacts sticking (high voltage level when the relay changes to OFF)PCB faulty; current leakage from motor or from wiring.
E61Insufficient heating during washingNTC sensor faulty; heating element faulty; wiring faulty; PCB faulty.
E62Overheating during washing (temperature higher than 88°C for a time higher than 5 min.)
E66Heating element power relay faulty (incongruence between sensing and relay)PCB faulty.
E68Current dispersion to earth (value of mains voltage different from main value)Current dispersion between between heating element and earth.
E69Heating element interruptedWiring faulty; Heating element for washing interrupted (thermofuse open).
E71Washing NTC sensor faulty (short- circuited or open)Wiring faulty; Washing NTC sensor faulty; PCB faulty.
E72Drying condenser NTC sensor faulty (voltage value out of limits, sensor short-circuited or open)Wiring faulty; Drying NTC sensor (condenser) badly positioned or faulty; WD board faulty.
E73Drying duct NTC sensor faulty (voltage value out of limits, sensor short-circuited or open)Wiring faulty; Drying NTC sensor (duct) badly positioned or faulty; WD board faulty.
E74Washing NTC sensor badly positioned
E82Error in selector reset positionPCB faulty (Wrong configuration data).
E83Error in selector reading

Electrolux PW9 washer error codes

Error codeCause/Action
01EAcknowledgement signal for water level not received within time allowed.
02 EDoor status acknowledgement signal not received during program operation.
03EDoor lock acknowledgement signal not received within time allowed.
07EWater level above parameter set for safety, during program.
10EWater level is above parameter set (10 scale units) after water discharge.