Samsung washer error codes

Of course it is hardly possible to keep in mind all codes, their meaning and ways to solve the problem, especially if you are not a repair engineer. That is why we have made this list of Samsung washer error codes.
The table below contains all Samsung washer error codes possible, and in most cases it just takes some time to return the machine to normal operation. We have included the fault codes for all modern models, including Samsung front load washer error codes.
The washer may display information codes to help you better understand what is occurring with your washer.
Samsung washer error codes
Samsung WA48J7700A, WA48J7770A Top Load Washer with activewash error codes
Samsung WA52J8060A, WA52J8700A Top Load Washer with activewash error codes
Samsung WA40J3000A series washer error codes
Samsung WA48J7770AWA2 washer error codes
Samsung Top Load WA52J8060A, WA52J8700A washer error codes
Samsung top load washer error codes
Samsung vrt washer error codes
Samsung popular error codes

Samsung washer error codes

CODE SYMBOLMEANINGSOLUTION
dc (error solution dc)Unbalanced load prevented your washer from spinningRedistribute the load, press the Start/Pause button
dSDoor is open when washer is runningClose the door tightly and restart the cycle.
If the code reappears, call for service
FL (error solution FL)Your washer failed to lock the doorClose the door tightly and restart the
cycle.
If the code reappears, call for service
HrThis error code appears when the
heater is 96 °C or above
Call for service
LE (error solution LE)Your washer has tried to fi ll, but has not
reached the proper water level
LE(1E)Leak problem or Waterlevel Sensor has
an abnormal reading.
LOThe door will not unlockMake sure the door is fi rmly closed.
Press the Power button to turn off your
washer, then turn it on again. If the
code reappears, call for service
nd (error solution nd)Your washer is not draining.
It can also mean that the unit senses a
small clog while draining
Clean the drain fi lter. Then, clean the
debris filter
If you are in the middle of a wash you
can try this fi rst:
1. Turn off the unit for 10 seconds and
then turn it on again.
2. Select the Spin Only cycle
3. Press the Start/Pause to drain the
water.
If it still does not drain, call for service
nF (error solution nF)Your washer has tried to fi ll but was
unsuccessful
Make sure the water faucets are open all
the way. Check for kinked hoses.
Check the inlet screens on the fi ll hoses.
If you use a Flood Safety Device, then
please remove the device and connect
the water hoses directly to the unit.
Check if the hot water supply hose is
connected.
You must connect the hot water supply
hose because hot water is supplied by
the Auto Temperature Control (A.T.C.)
function if the temperature of the cold
water is lower than 59°F
nF1This error code appears when the
water temperature is 50 °C or above
for 8 seconds or longer in the Wool and
Delicate course
Please connect the hot/cold water hose
connection correctly
OE (error solution OE)Water detected over the safe water
level.
Call for service
E2Jammed key.
tE (error solution tE)Temperature sensor problemRestart the cycle.
If the code reappears, call for service
3E (error solution 3E)Motor problem.
AECommunication error between SUB
PBA and MAIN PBA
SFSystem error
Suds (error solution SUdS)Too many suds are detected during the
washing session.
The unit is put on hold until the suds
are reduced. Then, the unit will go back
into the operation.
When it fi nishes washing, "End" and
"SUdS" codes will blink in turn.
Reduce the amount of detergent you
use
dE (error solution dE)Close the door
4E (error solution 4E)Make sure the water source is turned on.
Clean the water hose mesh filter
Check the water pressure.
5E (error solution 5E)Clean the debris filter.
Make sure the drainage hose is installed correctly
UE (error solution UE)Laundry load is unbalanced; loosen any tangled laundry. If only one
item of clothing needs washing, such as a bathrobe or jeans, the final
spin result might be unsatisfactory and an "UE" error message will be
shown in the display window
cEContact after-sales service. Call 1-800-SAMSUNG (726-7864) or visit
the website at samsung.com
HEWater heater errorHE, HE1 is displayed if the water temperature rises by 7 C or more in 1 Min
or by 2 C or less 20 Min after heating process has started.
The error can be cleared by turning POWER switch OFF.
1E (error solution 1E)Water pressure switch error* Generated Frequency Signal of WATER LEVEL (WIL) SIW (KHz)

Normal Level = Abnormal W/L Frequency
Low Level = 30.00 Khz High Level = 15.00 Khz

If the same signal is detected for more than 5 seconds, it is a PRESSURE SWITCH Error.
When this error occurs the drain pump will operate for 3 min.
and the display will show 1 E indicating a pressure switch error.
11 EWater leakage erorWater Leakage error occurs when the water drains naturally, (by leakage)
after the washing program starts.
8EOver current errorIPM fault signal (this is caused by the overload of the MICOM INTO during motor action).

IPM: Integrated power module. The IPM controls the motor.

If the fault (low signal) happens to be sensed even once during the washing/rinsing stage,
the motor stops immediately. However, during the dehydrating stage the signal is to be
sensed, when the number of signals reads more than 6 per 500ms during the Washing
or Rinsing cycle action.

If the motor stops working, in one direction ten times, “8E” Error is displayed.

During dehydrating, when the overload is sensed, the motor stops working at once
and then feeds back to the initial stage of the dehydration unbalance sensing. When the
feed back has occcurred twice, Error “8E” is displayed during the dehydrating unbalance
sensing, No error happens by overload sensing. When it happens at more than 800rpm,
the process is stopped compulsorily. Power Switch OFF can clear the overload error.
2E (error solution 2E)Internal control board failureUnplug the washer for 5 minutes to reset the electronic control board.
Plug the washer back in.
If the code returns, replace the electronic control board.

Samsung WA48J7700A, WA48J7770A Top Load Washer with activewash error codes

Washing machines Samsung WA48J7700A, WA48J7770A have the top loading. These are classical washers in white casing. Compactness is the main advantage of such vertical models, which is usually the determining factor for buyers. Having a standard height, such machines have a width and depth, which are significantly smaller than the front models usually have.

CodeAction
1CThe Water Level sensor is not working properly.
• Check WaterLevel Sensor wire harness.
• If the information code remains, contact a customer service centre.
NOTE
When the washer displays “1C”, the washer do draining for 3 minutes. During this time, the Power button is inoperative.
3CCheck the motor for operation.
• Try restarting the cycle.
• If the problem continues, call for service.
4CWater is not supplied.
• Make sure the water taps are open.
• Make sure the water hoses are not clogged.
• Make sure the water taps are not frozen.
• Make sure the washing machine is operating with sufficient water pressure.
• Make sure that the cold water tap and the hot water tap are properly connected.
• Clean the mesh filter as it may be clogged.
NOTE
When the washer displays “4C”, the washer do draining for 3 minutes. During this time, the Power button is inoperative.
4C2• Make sure the cold water supply hose is firmly connected to the cold water tap.
If it is connected to the hot water tap, the laundry may be deformed with some cycles.
5CWater is not draining.
• Make sure the drain hose is not frozen or clogged.
• Make sure the drain hose is positioned correctly, depending on the connection type.
• Clean the debris filter as it may be clogged.
• Make sure the drain hose is straightened all the way to the drain system.
• If the information code remains, contact a customer service centre.
9C1The electronic control needs to be checked (Over Voltage Check).
• Check the PCB and wire harness.
• Check if power is supplied properly.
• If the information code remains, contact a customer service centre.
9C2Low voltage detected
• Check if the power cord is plugged in.
• If the information code remains, contact a customer service centre
AC6Inverter Communication problem
• Check the Inverter PCB and wire harness.
• If the information code remains, contact a customer service centre.
dC (error solution dc)Operating the washer with the door open.
• Make sure the door is properly closed.
• Make sure laundry is not caught in the door.
HCHigh temperature heating check
• If the information code remains, contact a customer service centre.
LC (error solution LC)Check the drain hose.
• Make sure the end of the drain hose is placed on the floor.
• Make sure the drain hose is not clogged.
• If the information code remains, contact a customer service centre.
NOTE
When the washer displays “LC”, the washer do draining for 3 minutes. During this time, the Power button is inoperative.
OCWater is overflowed.
• Restart after spinning.
• If the information code remains on the display, contact a local Samsung service centre
PCWhen position of the clutch can't be detected.
• If the information code remains, contact a customer service centre.
PC1After position of the clutch is detected, if the signal of the clutch hall goes wrong.
• If the information code remains, contact a customer service centre.
Ub (error solution Ub)Spinning does not work.
• Make sure laundry is spread out evenly.
• Make sure the washing machine is on a flat, stable surface.
• Redistribute the load. If only one item of clothing needs washing, such as a bathrobe or pair of jeans, the final spin result might be unsatisfactory, and an “Ub” check message will be shown in the display.

Samsung WA52J8060A, WA52J8700A Top Load Washer with activewash error codes

Samsung WA52J8060A, WA52J8700A top load washers have a maximum load, in spite of their small proportions. These vertical washing machines are equipped with a spacious drum, so you can download as many kilograms of clothes as in machines with frontal load. The possibility to add clothes into the washer and the absence of costly repairs of the glass hatch or rubber seals are another great advantages of these washers.

Information CodeMeaningAction
Ub (error solution Ub)Unbalanced load prevents washer from spinning.Redistribute the load, and then press the Start/Pause button.
dC1The washer did not properly lock the door.Make sure the door is firmly closed. Restart the washer. If the code reappears, call customer service.
5CThe washer does not drain. The washer may detect a small clog while draining.1. Restart the washer.
2. Select the Spin Only cycle.
3. Press the Start/Pause button to drain the water.
If the washer still does not drain, call customer service.
4CYour Washer has tried to fill but was unsuccessful.
Check if the hot water supply hose is connected.
Check for the water taps and hoses connection(hose bent and inlet screens). If using a flood safety device, remove the device and directly connect the water hoses to the washer.
The hot water supply hose must be connected because the Auto Temperature Control (A.T.C.) function supplies hot water if the temperature of cold water is lower than 59 °F.
tC1Temperature sensor problemRestart the washer. If the code reappears, call customer service.
3CMotor problem.
dc (error solution dc)Lid is open when washer is running.Close the lid tightly and restart the cycle. If the code reappears, call for service.
dC1Your washer failed to lock the lid
LC (error solution LC)Water level problem.Call customer service.
OC/1CWater level sensor problem
bC2Jammed button.
ACCommunication error (SUB (sensor) PBA - MAIN PBA).
AC3Communication error (DR Module - MAIN PBA).
AC4Communication error (WIFI PBA - MAIN PBA)
AC5Communication error (LCD PBA - MAIN PBA)
AC6Communication error (Inverter PBA - MAIN PBA)
8C/8C2MEMS sensor problem
4C2This occurs when the temperature exceeds 50, for over 8 seconds in the Wool and Delicates course.
PCWhen position of the clutch can’t be detected.
PC1After position of the clutch is detected, if the clutch position is wrong, occurs error
Suds (error solution SUdS)The washer has detected too many suds. The washer will stop operating until the amount of suds has reduced. The washer will then resume normal operation.

Samsung WA40J3000A series washer error codes

The washer Samsung WA40J3000A is a classic top-loading washer. It is optimal in price-quality ratio. Moreover, you can take advantage of its compact proportions and convenient loading.

CODE SYMBOLMEANINGSOLUTION
Hot LED FlashesLid is open when washer is running.Close the lid tightly and restart the cycle. If the code reappears, call for service.
Warm LED FlashesCommunication error between SUB PBA and MAIN PBA.Call for service.
Cold LED FlashesA button is not working properly.
Tap Cold LED FlashesThe Water Level sensor is not working properly.
!!! When the Tap Cold LED is flashing, the washer drains for 3 minutes. During this time, the Power button is inoperative.
Extra Large LED FlashesYour Washer has tried to fill but was unsuccessful.
!!! When the Extra Large LED is flashing, the washer drains for 3 minutes. During this time, the Power button is inoperative.
Make sure the water faucets are open all the way. Check for kinked hoses.
Check the inlet screens on the fill hoses.
If you use a Flood Safety Device, remove the device and connect the water hoses directly to the unit.
Check if the hot water supply hose is connected.You must connect the hot water supply hose because hot water is supplied by the Auto Temperature Control (A.T.C.) function.
Large LED FlashesYour Washer has tried to fill but has not reached the proper water level.
!!! When the Large LED is flashing, the washer drains for 3 minutes. During this time, the Power button is inoperative.
Call for service.
Medium LED FlashesA fault is detected in the water level sensor.
Small LED FlashesYour washer is not draining. It can also mean that the unit senses a small clog while draining.Do the following:
1) Turn off the unit and turn it on again.
2) Select only the Spin Cycle.
3) Press the Start/Pause to drain the water.
If it still does not drain, call for service.
Hot & Warm LEDs flashUnbalanced load prevented your Washer from spinning.Redistribute the load, and then press the Start/ Pause button.
Hot & Cold LEDs flashMotor not running properly.Restart the cycle by presssing the Start/Pause button. If the code reappears, call for service.
Hot & Tap Cold LEDs flashMems sensor is not working properlyCall for service.
Hot & Extra Large LEDs flashDoor lock is not working properlyClose the lid tightly and restart the cycle. If the code reappears, call for service.
Hot & Large LEDs flashDoor lock is not working properly.
Hot & Medium LEDs flashThermistor is not working properly.Call for service.
Hot & Small LEDs flashThe temperature of the supplied water is so high.Ensure that the cold water tap and the hot water tap are connected correctly. If the code reappears, call for service.

Samsung WA48J7770AWA2 washer error codes

The washer Samsung WA48J7770AWA2 is a classical top-loading washer. Reap its benefits at an optimal in price.

Information CodeMeaningAction
Ub (error solution Ub)Unbalanced load prevents washer from spinning.Redistribute the load, and then press the Start/Pause button.
dC1The washer did not properly lock the door.Make sure the door is firmly closed. Restart the washer. If the code reappears, call customer service
5CThe washer does not drain. The washer may detect a small clog while draining.1. Restart the washer.
2. Select the Spin Only cycle.
3. Press the Start/Pause button to drain the water.
If the washer still does not drain, call customer service
4CYour Washer has tried to fill but was unsuccessful. Check if the hot water supply hose is connected.Check for the water taps and hoses connection(hose bent and inlet screens). If using a flood safety device, remove the device and directly connect the water hoses to the washer.
The hot water supply hose must be connected because the Auto Temperature Control (A.T.C.) function supplies hot water if the temperature of cold water is lower than 59 °F.
tC1Temperature sensor problem.Restart the washer. If the code reappears, call customer service.
3CMotor problem.
dc (error solution dc)Lid is open when washer is running.Close the lid tightly and restart the cycle. If the code reappears, call for service.
dC1Your washer failed to lock the lid.
LC (error solution LC)Water level problem.Call customer service.
OC/1CWater level sensor problem
bC2Jammed button.
ACCommunication error (SUB (sensor) PBA - MAIN PBA).
AC3Communication error (DR Module - MAIN PBA).
AC4Communication error (WIFI PBA - MAIN PBA)
AC5Communication error (LCD PBA - MAIN PBA)
AC6Communication error (Inverter PBA - MAIN PBA)
8C/8C2MEMS sensor problem
4C2This occurs when the temperature exceeds 50, for over 8 seconds in the Wool and Delicates course
PCWhen position of the clutch can’t be detected.
PC1After position of the clutch is detected, if the signal of the clutch hall goes wrong, occurs error.
Suds (error solution SUdS)The washer has detected too many suds. The washer will stop operating until the amount of suds has reduced. The washer will then resume normal operation.

Samsung Top Load WA52J8060A, WA52J8700A washer error codes

Samsung Top Load washers WA52J8700A, WA52J8060A are 27-inch-wide energy star rated washing machines. They have nice white color of the case. The super speed cycle of washing is their distinguishing feature.

CodeMeaning
1CThe WaterLevel sensor is not working properly.
• Check WaterLevel Sensor wire harness.
• If the information code remains, contact a customer service centre.
NOTE
When the washer displays “1C”, the washer do draining for 3 minutes. During this time, the Power button is inoperative.
3CCheck the motor for operation.
• Try restarting the cycle.
• If the problem continues, call for service
4CWater is not supplied.
• Make sure the water taps are open.
• Make sure the water hoses are not clogged.
• Make sure the water taps are not frozen.
• Make sure the washing machine is operating with sufficient water pressure.
• Make sure that the cold water tap and the hot water tap are properly connected.
• Clean the mesh filter as it may be clogged.
NOTE
When the washer displays “4C”, the washer do draining for 3 minutes. During this time, the Power button is inoperative.
4C2• Make sure the cold water supply hose is firmly connected to the cold water tap.
If it is connected to the hot water tap, the laundry may be deformed with some cycles.
5CWater is not draining.
• Make sure the drain hose is not frozen or clogged.
• Make sure the drain hose is positioned correctly, depending on the connection type.
• Clean the debris filter as it may be clogged.
• Make sure the drain hose is straightened all the way to the drain system.
• If the information code remains, contact a customer service centre.
9C1The electronic control needs to be checked (Over Voltage Error).
• Check the PCB and wire harness.
• Check if power is supplied properly.
• If the information code remains, contact a customer service centre.
9C2Low voltage detected
• Check if the power cord is plugged in.
• If the information code remains, contact a customer service centre.
AC6Inverter Communication problem
• Check the Inverter PCB and wire harness.
• If the information code remains, contact a customer service centre.
dC (error solution dC)Operating the washer with the door open.
• Make sure the door is properly closed.
• Make sure laundry is not caught in the door.
HCHigh temperature heating check.
• If the information code remains, contact a customer service centre.
LC (error solution LC)Check the drain hose.
• Make sure the end of the drain hose is placed on the floor.
• Make sure the drain hose is not clogged.
• If the information code remains, contact a customer service centre.
NOTE
When the washer displays “LC”, the washer do draining for 3 minutes. During this time, the Power button is inoperative.
OCWater is overflowed.
• Restart after spinning.
• If the information code remains on the display, contact a local Samsung service centre.
PCWhen position of the clutch can't be detected.
• If the information code remains, contact a customer service centre.
PC1After position of the clutch is detected, if the signal of the clutch hall goes wrong.
• If the information code remains, contact a customer service centre.
Ub (error solution Ub)Spinning does not work.
• Make sure laundry is spread out evenly.
• Make sure the washing machine is on a flat, stable surface.
• Redistribute the load. If only one item of clothing needs washing, such as a bathrobe or pair of jeans, the final spin result might be unsatisfactory, and an “Ub” check message will be 1. shown in the display

Samsung top load washer error codes

CODE SYMBOLMEANINGSOLUTION
dc (error solution dc)Unbalanced load prevented your washer from spinning.Redistribute the load, press the Start/Pause button.
dLDoor is unlocked when washer is running.Press the Power button to turn off your washer, then restart the cycle. If the code reappears, call for service.
dSDoor is open when washer is running.Close the door tightly and restart the cycle. If the code reappears, call for service.
FL (error solution FL)Your washer failed to lock the door.
HrWater temperature control problem. (Heater Control problem)Call for service.
LE (error solution LE)Your washer has tried to fill but has not reached the proper water level.
LOThe door will not unlock.Make sure the door is firmly closed. Push the Power button to turn off your washer, then turn it on again. If the code reappears, call for service.
E3 (error solution E3)Motor not running properly.Restart the cycle by pressing the Start/Pause button. If the code reappears, call for service.
nd (error solution nd)Your washer is not draining. It can also mean that the unit senses a small clog while draining.Before calling for service, check the following. Clean the filter
1. Turn off the unit for 10 seconds and then turn it on again.
2. Select only the Spin Cycle.
3. Press the Start/Pause to drain the water.
If it still does not drain, call for service.
nF (error solution nF)Your washer has tried to fill but was unsuccessful.Make sure the water faucets are open all the way. Check for kinked hoses. Check the inlet screens on the fill hoses.
nF1The hot/cold water hose connection is not correct.Please connect the hot/cold water hose connection correctly.
SrProblem with control.Call for service.
OE (error solution OE)A fault is detected in the water level sensor.
E2Jammed Key.
tE (error solution tE)Temperature sensor problem.Restart the cycle. If the code reappears, call for service.
3E (error solution 3E)Motor problem.
2E (error solution 2E)High/Low voltage detected.
7EAg+ Kit problemCall for service
AECommunication error between SUB PBA and MAIN PBA
SF1, SF2, SF3System error
Suds (error solution SUdS)Too many suds are detected during the washing session. The unit is put on hold until the suds are reduced. Then, the unit will go back to the operation. When it finishes washing, End and SUdS codes will blink in turn.To prevent it, cut down on detergents.

Samsung vrt, front load washer error codes

CODE SYMBOLMEANINGSOLUTION
dc (error solution dc)Unbalanced load prevented your washer from spinning.Redistribute the load, press the Start/Pause button.
dLDoor is unlocked when washer is running.Press the Power button to turn off your washer, then restart the cycle. If the code reappears, call for service.
dSDoor is open when washer is running.Close the door tightly and restart the cycle. If the code reappears, call for service.
FL (error solution FL)Your washer failed to lock the door.
HrWater temperature control problem. (Heater control problem)Call for service.
LE (error solution LE)Your washer has tried to fill but has not reached the proper water level.
LOThe door will not unlock.Make sure the door is firmly closed. Press the Power button to turn off your washer, then turn it on again. If the code reappears, call for service.
nd (error solution nd)Your washer is not draining. It can also mean that the unit senses a small clog while draining.Before calling for service, check the following. Clean the filter
1. Turn off the unit for 10 seconds and then turn it on again.
2. Select the Spin Only cycle
3. Press the Start/Pause to drain the water.
If it still does not drain, call for service.
Your washer has tried to fill but was unsuccessful.Make sure the water faucets are open all the way. Check for kinked hoses. Check the inlet screens on the fill hoses.
nF (error solution nF)Check if the hot water supply hose is connected.You must connect the hot water supply hose because hot water is supplied by the Auto Temperature Control (A.T.C.) function if the temperature of the cold water is lower than 59°F.
nF1The hot/cold water hose connection is not correct.Please connect the hot/cold water hose connection correctly.
SrProblem with control.Call for service.
OE (error solution OE)A fault is detected in the water level sensor.
E2Jammed key.
tE (error solution tE)Temperature sensor problem.Restart the cycle. If the code reappears, call for service.
3E (error solution 3E)Motor problem.
2E (error solution 2E)High/Low voltage detected.
7EAg+ Kit problemCall for service
AECommunication error between SUB PBA and MAIN PBA
SF1, SF2, SF3System error
Suds (error solution SUdS)Too many suds are detected during the washing session.To prevent it, cut down on detergents.
The unit is put on hold until the suds are reduced. Then, the unit will go back to the operation. When it finishes washing, “End” and “SUdS" codes will blink in turn.

Samsung poular error codes

  • The engine tachometer error is displayed in the form of Samsung washer error code 3e. This error can mean the following breakdowns: faulty contact connection of the engine; motor winding damage; faulty contacts and connections of the tachometric alternator; engine lock objects (for example, bolts).
  • Water inlet error is displayed as Samsung washing 4e error code. The reason for this might be the following failures: the ingress of foreign objects in the water valve; faulty contacts and connections of the water valve; improper connection of the hot and cold water feed; there is no connection of the drain hose to the detergent container. You should check whether the transparent hose is not kinked or torn.