WasherErrorCodes

The well-made dishwasher is a guarantee of more brilliant dishes without any physical efforts! Nevertheless, even the nice apparatus such, as General Electric, can break at any time, nobody is insured from this. What to do in this case?
In the first place, do not panic. Because all the GE dishwashers are fit with the GE washer repair troubleshooting system allowing to quickly reveal the cause of a breakdown on special error codes and remove a disrepair.
GE Appliances GTWN series, GFWH series, GBVH series, GFWN series, GFWR series, GFWS seris, PFWS series washer troubleshooting
GE Appliances WASR series washer troubleshooting
GE LISR series washer troubleshooting

GE Appliances GTWN series, GFWH series, GBVH series, GFWN series, GFWR series, GFWS seris, PFWS series washer troubleshooting

If your GE Appliances washer is experiencing an issue, you’ve come to the right place! On this page you’ll find troubleshooting advice for models that belong to the following series: GTWN, GFWH, GBVH, GFWN, GFWR, GFWS, and PFWS. The table was created by engineers from the General Electric company.

Problem	Possible Causes	What To Do
Not draining Not spinning Not tumbling	Load is out of balance	Redistribute clothes and run drain & spin or rinse & spin. Increase load size if washing small load containing heavy and light items
	Pump clogged
	Drain hose is kinked or improperly connected	Straighten drain hose and make sure washer is not sitting on it.
	Household drain may be clogged	Check household plumbing. You may need to call a plumber
	Drain hose siphoning; drain hose pushed too far down the drain	Ensure there is an air gap between hose and drain.
Leaking water	Door gasket is damaged	Check to see if gasket is seated and not torn. Objects left in pockets may cause damage to the washer (nails, screws, pens, pencils) Water may drip from the door when the door is opened. This is a normal operation. Carefully wipe off rubber door seal. Sometimes dirt or clothing is left in this seal and can cause a small leak
	Check back left of washer for water	If this area is wet. you have oversudsing condition. Use less detergent.
	Fill hoses or drain hose is improperly connected	Make sure hose connections are tight at washer and faucets and make sure end of drain hose is correctly inserted in and secured to drain facility.
	Household drain may be clogged	Check household plumbing. You may need to call a plumber.
	Dispenser clogged	Powder soap may cause clogs inside the dispenser and cause water to leak out the front of the dispenser. Remove drawer and clean both drawer and inside of dispenser box.
	Incorrect use of detergent	Use only HE and correct amount of detergent.
	Dispenser box cracked	If new installation, check for crack on inside of dispenser box.
Clothes too wet	Load is out of balance	Redistribute clothes and run drain & spin or rinse & spin. Increase load size if washing small load containing heavy and light items. The machine will slow the spin speed down to 410 rpm if it has a hard time balancing the load. This speed is normal.
	Overloading	The dry weight of the load should be less then 16 lbs.
	Drain hose is kinked or improperly connected	Straighten drain hose and make sure washer is not sitting on it.
	Household drain may be clogged	Check household plumbing. You may need to call a plumber
	Drain hose siphoning; drain hose pushed too far down the drain	Ensure there is an air gap between hose and drain.
Incomplete cycle or timer not advancing	Automatic load redistribution	Timer adds 3 minutes to cycle for each rebalance. 11 or 15 rebalances may be done. This is normal operation. Do nothing; the machine will finish the wash cycle.
	Drain hose is kinked or improperly connected	Straighten drain hose and make sure washer is not sitting on it
	Household drain may be clogged	Check household plumbing. You may need to call a plumber
	Drain hose siphoning; drain hose pushed too far down the drain	Ensure there is an air gap between hose and drain.
Loud or unusual noise; vibration or shaking	Cabinet moving	Washer is designed to move 1/4” to reduce forces transmitted to the floor. This movement is normal.
	All rubber leveling legs are not firmly touching the floor	Push and pull on the back right and then back left of your washer to check if it is level. If the washer is uneven, adjust the rubber leveling legs so they are all firmly touching the floor and locked in place. Your installer should correct this problem.
	Unbalanced load	Pause unit, open door and manually redistribute load. To check machine, run rinse and spin with no load. If normal, unbalance was caused by load
No power/ washer not working or dead	Washer is unplugged	Make sure cord is plugged securely into a working outlet.
	Water supply is turned off	Turn both hot and cold faucets fully on
	Circuit breaker/fuse is tripped/ blown	Check house circuit breakers/fuses. Replace fuses or reset breaker. Washer should have separate outlet
	Automatic self system checks	First time the washer is plugged in, automatic checks occur. It may take up to 20 seconds before you can use your washer. This is normal operation.
Snags, holes, tears, rips or excessive wear	Overloaded	Do not exceed maximum recommended load sizes.
	Pens, pencils, nails, screws or other objects left in pockets	Remove loose items from pockets.
	Pins, snaps, hooks, sharp buttons, belt buckles, zippers and sharp objects left in pockets	Fasten snaps, hooks, buttons and zippers.
Control time wrong or changes	This is normal	During spin the washer may need to rebalance the load sometimes to reduce vibrations. When this happens, the estimated time is increased causing time left to increase or jump.
Not enough water	This is normal	Horizontal washers do not require the tub to fill with water like topload washers
Washer pauses or has to be restarted, or washer door is locked and will not open	Pump clogged
Door unlocks or press Start and machine doesn’t operate	This is normal	Front-load washers start up differently than top-load washers, and it takes 30 seconds to check the system. The door will lock and unlock.
	Incorrect operation	Simply open and close the door firmly; then press Start.
Water does not enter washer or enters slowly	Automatic self system checks	After Start is pressed, the washer does several system checks. Water will flow 60 seconds after Start is pressed.
	Water supply is turned off	Turn on both hot and cold faucets fully
	Water valve screens are stopped up	Turn off the water source and remove the water connection hoses from the upper back of the washer. Use a brush or toothpick to clean the screens in the machine. Reconnect the hoses and turn the water back on.
	Inlet hose screen washers are stopped up	Turn off the water source and remove the inlet hoses from the wall faucets. Use a brush or toothpick to clean the screen washers in the end of the hoses. Reconnect the hoses and turn the water back on.
Wrinkling	Improper sorting	Avoid mixing heavy items (like work clothes) with light items (like blouses).
	Overloading	Load your washer so clothes have enough room to move freely.
	Incorrect wash cycle	Match cycle selection to the type of fabric you arewashing (especially for easy care loads).
	Repeated washing in water that is too hot	Wash in warm or cold water
Grayed or yellowed clothes	Not enough detergent	Use correct amount of detergent.
	Not using HE (high efficiency) detergent	Use only HE detergent.
	Hard water	Use hottest water safe for fabric. Use a water conditioner like Calgon brand or install a water softener
	Water is not hot enough	Make sure water heater is delivering water at 120°–140°F (48°–60°C).
	Detergent is not dissolving	Try a liquid HE detergent.
	Dye transfer	Sort clothes by color. If fabric label states wash separately, unstable dyes may be indicated.
Colored spots	Incorrect use of fabric softener	Check fabric softener package for instructions and follow directions for using dispenser
	Dye transfer	Sort whites or lightly colored items from dark colors. Promptly remove wash load from washer.
Water temperature is incorrect	Water supply is improperly connected	Make sure hoses are connected to correct faucets.
	House water heater is not set properly	Make sure house water heater is delivering water at 120°–140°F (48°–60°C).
Slight variation in metallic color	This is normal	Due to the metallic properties of paint used for this unique product, slight variations of color may occur due to viewing angles and lighting conditions
Bad odor inside your Washer	Washer unused for a long time, not using recommended quality of HE detergent or used too much detergent	Run a Basket Clean cycle. In case of strong odor, you may need to run the Basket Clean cycle more than once. Use only the amount of detergent recommended on the detergent container. Use only HE (high efficiency) detergent. Always remove wet items from the washer promptly after machine stops running. Leave the door slightly open for the water to air dry. Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on or in this or any other appliance.
Detergent leak	Incorrect placement of detergent insert	Make sure detergent insert is properly located and fully seated. Never put detergent above max line.
	This is normal	It is normal operation to see detergent leak on door gasket about 20 seconds after filling the dispenser
Improper dispensing of softener or bleach	Dispenser clogged	Monthly clean the dispenser drawer to remove buildup of chemicals.
	Softener or bleach is filled above the max line	Make sure to have the correct amount of softener or bleach.
	Softener or bleach cap issue	Make sure softener and bleach cap for dispenser are seated or they will not work
Dispenser drawer not dispensing properly	Laundry detergent packet placed in dispenser drawer	Laundry detergent packets should not be used in the dispenser. They should only be added directly to the wash basket following the manufacturer's directions.
Pump running while washer is not in use	Clog in sump drain	This is normal. Drain sump is detecting an undesired water fill level from a potential open faucet. Shut off water valve and inspect water valve for blockage.

GE Appliances WASR series washer troubleshooting

GE Appliances WASR series is comprised of top-loading washers. One of the most popular models from this range is the WASR3110. It offers a lot of adjustments in terms of load size (from small and medium to large and Super), wash and spin speed, temperature, and rinsing options.

Problem	Possible Causes	What To Do
SensorWash indicator light (on some models) is not illuminated	Washer is NOT in a wash fill cycle or a warm rinse fill cycle	This is normal. Light only illuminates during wash fills and warm rinse fills.
SensorWash wash temperature is incorrect	The washer is in a cold rinse cycle	This is normal. The SensorWash feature is designed not to activate during a cold rinse cycle so that the coldest water available is used.
(Review SensorWash in the About washer features section)	All the water in the water heater has been used	Wait until the water in the water heater is heated to the correct temperature.
Too many suds	Type of detergent	Switch to a lower sudsing detergent brand and follow instructions on package.
	Very soft water	Try less detergent.
	Too much detergent.	Measure your detergent carefully. Use less soap if you have soft water, a smaller load, or a lightly soiled load
Water leaks	Fill hoses or drain hose is improperly connected	Make sure hose connections are tight at faucets and make sure end of drain hose is correcdy inserted in and secured to drain facility.
	Household drain may be clogged	Check household plumbing. You may need to call a plumber.
	Constant water pressure to the fill hoses at the water source	Tighten hoses at die faucets and turn die water off after each use. Check condition of die fill hoses; diey may need replacement after 5 years.
	Using too much detergent in washer	Use less detergent. Use less soap if you have soft water, a smaller load, or a lightly soiled load.
Water temperature is incorrect	Control is not set properly	Check water temperature control and adjust.
	Water supply is turned off or improperly connected	Turn both hot and cold faucets fully on and make sure hoses are connected to correct faucets.
	Water valve screens are stopped up	Turn off die rater source and remove die water connection hoses from die upper back of the washer. Use a brush or toothpick to clean die screens in die machine. Reconnect the hoses and turn the water back on.
	House water heater is not set properly	Make sure house water heater is delivering water at 120°F.-140°F. (48°C.-60°C.).
Water won’t drain	Drain hose is kinked or improperly connected	Straighten drain hose and make sure washer is not sitting on it. Top of drain outlet should be less than 8 ft (2.5 m) above floor.
Washer pauses in cycle	The washer normally pauses between washing steps
Washer won’t operate	Washer is unplugged	Make sure cord is plugged securely into a working outlet
	Water supply is turned off	Turn both hot and cold faucets fully on
	Controls are not set properly	Check controls and make sure Cycle knob is pulled out properly to ON position
	Lid is open	Close lid and pull Cycle knob out to ON position.
	Circuit breaker/fuse is tripped/blown	Check house circuit breakers/fuses. Replace fuses or reset breaker. Washer should have separate outlet.
Clothes too wet	Incorrect spin cycle selected	Make sure the spin cycle selected matches the load you selected are washing. Some fabrics will feel wetter when rinsed with cold water
Colored spots	Incorrect use of fabric softener	Check fabric softener package for instructions and follow directions for using dispenser Pretreat stain and rewash.
	Dye transfer	Sort whites or lightly colored items from dark colors
Grayed or yellowed clothes	Not enough detergent	Use more detergent (especially with larger loads)
	Hard water	Use a water conditioner like Calgon brand or install a water softener.
	Water is not hot enough	Make sure water heater is delivering water at 120°F.–140°F. (48°C.–60°C.).
	Washer is overloaded	Select load size to match clothes load
	Detergent is not dissolving	Add detergent as wash basket fills with water before you load clothes
	Dye transfer	Sort clothes by color. If fabric label states wash separately unstable dyes may be indicated.
Lint or residue on clothes	Clothes are air or line dried	If you do not dry' your clothes widi a clodies dryer, your clothes may retain more lint.
	Incorrect sorting	Separate lint producers from lint collectors.
	Washing too long	Wash small loads for a shorter time dian larger loads.
	Detergent not dissolving	Add detergent as wash basket fills with water, before you load clothes. Try a liquid detergent. Use warmer water temperature.
	Overloading	Load clodies no higher than die top row of holes in die washer tub. Make sure load size selector matches clodies load size.
	Incorrect use of fabric softener	Check fabric softener package for instructions and follow directions for using dispenser.
Pilling	Result of normal wear on poly-cotton blends and fuzzy fabrics	While this is not caused by the washer, you can slow the pilling process by washing garments inside out.
Snags, holes, tears, rips or excessive wear	Pins, snaps, hooks, sharp buttons, belt buckles,zippers, and sharp objects left in pockets	Fasten snaps, hooks, buttons, and zippers. Remove loose items like pins, objects in pockets and sharp buttons. Turn knits (which snag easily) inside out.
	Undiluted chlorine bleach	Check bleach package instructions for proper amount. Never add undiluted bleach to wash or allow clothes to come in contact with undiluted bleach.
	Chemicals like hair bleach or dye, permanent wave solution	Rinse items diat may have chemicals on diem before washing.
Wrinkling	Improper sorting	Avoid mixing heavy items (like work clothes) with light items (like blouses). Try a fabric softener.
	Overloading or incorrect water level	Load your washer so clothes have enough room to move freely.
	Incorrect wash and dry cycles	Match Cycle selection to the type of fabric you are washing (especially for easy care loads).
	Repeated washing in water that is too hot	Wash in warm or cold water.

GE LISR series washer troubleshooting

One of the most popular models from the GE LISR series is the GE LISR310 washer. It is a top-loading washing machine with the maximum load capacity of 7.5 kg. Depending on the characteristics of each load, a user has a chance to choose any of three wash/spin speeds, four load sizes, and four temperatures.

Problem	Possible Causes	What to Do
Washer Won’t Operate	Washer is unplugged	Make sure cord is plugged securely into a working outlet.
	Water supply is turned off	Turn both hot and cold taps fully on.
	Controls are not set properly	Check controls and make sure Cycle knob is pulled out to an on position.
	Lid is open	Close lid and pull Cycle knob out to an on position.
	Circuit breaker/fuse is tripped/blown	Check house circuit breakers/fuses. Replace fuses or reset breaker. Washer should have separate outlet.
Water Temperature is Incorrect	Control is not set properly	Check water temperature control and adjust.
	Water supply is turned off or improperly connected	Turn both hot and cold taps fully on and make sure hoses are connected to correct taps.
	Water valve screens are stopped up	Turn off the water source and remove the water connection hoses from the upper back of the washer. Use a brush or toothpick to clean the screens in the machine. Reconnect the hoses and turn the water source back on.
	House water heater is not set properly	Make sure house water heater is delivering water at 48°C.-65°C. (120°F.-150°F.).
Water Won't Drain	Drain hose is kinked or improperly connected	Straighten drain hose and make sure washer is not sitting on it. Top of drain oudet should be less than lm (3 ft.) above floor.
Water Leaks	Fill hoses or drain hose is improperly connected	Make sure hose connections are tight at taps and make sure end of drain hose is correctly inserted in and secured to drain facility.
	Household drain may be clogged	Check household plumbing. You may need to call a plumber.
	Constant water pressure to the fill hoses at the water source	Tighten hoses at the taps and turn the water off after each use. Check condition of the fill hoses; they may need replacement after 5 years.
Washer is Noisy	Washer is uneven	Make sure washer is level and firm to the floor.
	Washer load is unbalanced	Push the Cycle knob in to stop the washer, open the lid and redistribute the load evenly. Close the lid and restart.
	Shipping rod has not been removed	Remove the shipping rod on the bottom right side of the washer just before sliding the washer in place. Do not use the washer with the shipping rod in place.
	Water is draining	There will be a gurgling, “sucking” sound prior to the spin cycle. This is normal and will stop as soon as the machine goes into the spin cycle.
Washer Pauses in Cycle	The washer normally pauses between washing steps
Clothes too Wet	Incorrect cycle	Make sure the cycle matches the selected load you are washing.
	This is normal for some fabrics
Lint or Residue on Clothes	Incorrect sorting	Separate lint producers from lint collectors.
	Washing too long	Wash small loads for a shorter time than larger loads.
	Detergent not dissolving	• For best performance always add detergent before adding clothes. If you use powdered detergent, pre-dissolve detergent in hot water before adding to washer. Try a liquid detergent. Use warmer water temperature.
	Overloading	Make sure load/water level setting matches load size.
	Too much bleach	Check bleach package for correct amount.
	Not enough detergent	Try using more detergent.
	Incorrect use of fabric softener	Check fabric softener package for instructions
Wrinkling	Improper loads	Avoid mixing heavy items (like work clothes) with light items (like blouses). Separate permanent press from other laundry. Try a fabric softener.
	Overloading or incorrect water level	Load your washer so clothes have enough room to move freely.
	Incorrect wash and dry cycles	Match Cycle selection to the type of fabric you are washing (especially for permanent press loads).
	Repeated washing in water that is too hot	Wash in warm or cold water with plenty of detergent.
Snags, Holes, Tears, Rips, or Excessive Wear	Pins, snaps, hooks, sharp buttons, belt buckles, zippers, and sharp objects left in pockets	Fasten snaps, hooks, buttons, and zippers. Remove loose items like pins, objects in pockets and sharp buttons. Turn knits (which snag easily) inside out.
	Undiluted chlorine bleach	Check bleach package instructions for proper amount. Never add undiluted bleach to wash or allow clothes to come in contact with undiluted bleach.
	Small tears or holes present before wash	Repair tears and holes before washing.
	Chemicals like hair bleach, hair dye, permanent wave solution and toilet bowl cleaners	Rinse items that may have chemicals on them before washing.
	Permanent press items naturally fray (especially collars and cuffs)	While this is not caused by the washer, you can slow the fraying process by washing small permanent press loads with a higher load/water level setting. Avoid washing heavy items (like towels)with permanent press items.
Shrinkage	Some fabrics wall naturally shrink in the wash	Hot water is more likely to cause shrinkage than cold water. Follow* directions on fabric care label.
Grayed Clothes	Not enough detergent (larger loads, heavy soil, and hard water might require more detergent)	Try using more detergent (especially with larger loads). If you live in a hard water area try using a water conditioner or install a water softener.
	Water is not hot enough	Make sure water heater is delivering water at48°C.-65°C. (120°F.-150°F.). Do not use the washer when hot water is used for other needs (dishes, baths, etc.).
	Washer is overloaded	Make sure load/water level setting matches load size.
	Soak time is too short	Soak at least SO minutes.
	Soaking with too little detergent	Use more detergent (especially with heavy soil).
	Detergent is not dissolving	Add detergent as wash basket fills with water before you load clothes.
	To restore grayed clothes, try one of the following	Put clothes through a wash cycle using hot water. Add a non-precipitating water softener. Use 2 1/2 times more than is recommended for normal water softening. Do not use detergent or soap. Allow clothes to go through a complete cycle. Repeat if necessary. Soak your clothes using a water softener instead of a soaking agent. Allow clothes to soak for about 20 minutes.
Yellowed Clothes	Not enough detergent on a consistent basis	Always use the recommended amount of detergent.
	Chlorine bleach may yellow some fabrics	Use non-chlorine bleach.
	Iron or manganese in water may cause yellowing or yellow spots	Use extra detergent plus a non-precipitating water softener dissolved in water and non-chlorine bleach. Run hot water for 2 minutes to help the pipes clean out iron buildup. Drain your house water heater occasionally. To remove spots spread stain area over a pan of boiling water and squeeze lemon juice through the stain.
Blue or Gray Spots	Incorrect use of fabric softener	Check fabric softener package for instructions To remove spots dampen the spots and rub with undiluted liquid detergent. Rewash, using chlorine bleach if it is safe for the fabric.
Too Many Suds	Type of detergent	Switch to a lower sudsing detergent brand and follow instructions on package.
	Very soft water	Try less detergent.
Pilling	Result of normal wear on poly-cotton blends	While this is not caused by the washer, you can slow the pilling process by washing poly-cotton blends inside out.