Mankind always seeks to optimize. The grounds of this aspiration are present everywhere, and brand household washing machines Speed Queen of the United States are no exception. The comfort of everyday use, special design and a wide range of models allows even the most demanding buyers to change their point of view on this kind of products. Troubleshooting system facilitates this. You can make yourself aware of it below. It will help to solve problems with breakdowns.
| Washer Symptom | Possible/Cause Solution |
|---|---|
| Load is Too Wet | • Wash load may be unbalanced. The washer may have limited the spin speed to prevent damage to the machine. Redistribute the load and run a Spin cycle. |
| • Load is too small. Add items to make full load. | |
| Wrong Water Temperature | • Make sure that the controls are properly set. |
| • Check fill hoses. Make sure hot faucet hose is connected to hot mixing valve (indicated with "H’ on the valve bracket) and cold faucet is connected to cold mixing valve (indicated with "C on the valve bracket). Make sure laundry room water heater is adjusted properly. | |
| • The Normal Eco cycle uses a colder water temperature. | |
| Control not responding to keypad selections | • Make sure Control Lock feature is off. If on. Control Lock light will be lit. |
| • Press and hold Signal Keypad for three seconds to turn off. | |
| Er. do on digital display | • The control senses that the door is open during a running cycle. |
| • Unplug the machine to clear this code. | |
| Er. dL on digital display | • The control senses that the door has unlocked during a running cycle. |
| • Unplug the machine to clear this code. | |
| Er. dr on digital display | • This code indicates that water is still in the washer at the end of the cycle. |
| • Check the drain hose and drain receptacle to make sure they are installed properly and not blocked. Foreign object trap in pump may be clogged. Clean the trap. Re- fer to Maintenance section. | |
| • Unplug the machine for 15 seconds to clear this code. | |
| Er. FL on digital display | • This code will appear if the washer has not reached the fill level after 30 minutes during a wash or rinse fill. Make sure hot and cold water faucets are turned on. |
| • Make sure that the fill hoses are not kinked or twisted. | |
| • Clean the screens in the water mixing valve and the filter screens located at the faucet end of the fill hoses. | |
| • Unplug the machine for 15 seconds to clear this code. | |
| Er. nF on digital display | • The washer has not filled to the proper water level. |
| No or very little change in water level has been sensed within 5 minutes of the current fill. Make sure hot and cold water faucets are turned on. | |
| • Make sure that the fill hoses are not kinked or twisted. | |
| • Clean the screens in the water mixing valve and the filter screens located at the faucet end of the fill hoses. | |
| • Unplug the machine for 15 seconds to clear this code. | |
| Er. OF on digital display | • This code indicates the washer has filled to the overflow level. |
| • The machine will begin to a ttempt to pump water out if the door is closed and locked. | |
| • Foreign object trap in pump may be clogged. Clean the trap. Re- fer to Maintenance section. | |
| • If the code does not clear, unplug the machine and call for serv- ice. | |
| Er. PS on digital display | • The control has detected trouble sensing the water fill level. Unplug the machine and call for service. |
| Er dU on digital display | • The control senses that the door will not unlock. |
| • Unplug the machine for three minutes to unlock the door. | |
| • If the code appears again, call for service. | |
| Er.dl on digital display | • This code indicates that the door has not locked. |
| • Make sure the door is closed all the way and try to start the cycle. | |
| • Open the door or unplug the machine to clear the code. | |
| • If this code continues, call for service. | |
| f r. ub on digital display | • This code indicates that the wash load was unbalanced. |
| • The unbalanced load may have limited the spin speed. Be sure to use proper load sizes. | |
| • Open the door or press the Power/Cancel keypad to clear this code. | |
| PF on digital display | • This code will be displayed If the control was in Delay Start Mode when a power failure occurred. |
| • The delayed start will be canceled. | |
| • Press the Power/Cancel Pad to clear the code. | |
| Er.SL on digital display | • This code will be displayed after a cycle for one minute, or until the Power/Cancel keypad is pressed, and indicates an over- sudsing condition. |
| • Laundry load may be oversudsing. Make sure you are using low sudsing, high efficiency (HE) detergent. If using non-HE deter- gent. use only 1 /2 of the detergent manufacturer's recommen- ded amount. | |
| • Laundry load may be overloaded. Make sure you are using prop- er load sizes. | |
| 5r. cycle time remaining on digital display | • The control has detected an oversudsing condition and is run- ning a special routine to remove the excess suds. |
| Display | Description | Cause/Corrective Action |
|---|---|---|
| EI01 | Transmission Failure | Communication failure. Re-aim external device and try again. |
| EI02 | Time-out Error | |
| EI03 | Invalid Command Code | Communication successful, but the command was not valid for this machine type, or the control could not perform the command in its current mode of operation. Ensure data is for current machine type and control is in correct mode. |
| EI04 | Expecting Upload Request | Communication failure. Re-aim external device and try again. |
| EI05 | Invalid or Out-of-Range Data | The value in at least one of the programming options is invalid or out of range. Recheck the programming option’s value and try again. |
| EI09 | CRC-I6 Error | Communication failure. Re-aim external dcvicc and try again. |
| EIOA | Framing Error | |
| EIOC | Time-out Exceeded | |
| EIOE | Encryption Error | Communication error. Re-aim external dcvicc and try again. If the problem persists, check that the security codc is correct. |
| EIOF | Infra-red Disabled | Communication failure or infra-red is disabled. Manually enable infra-red on control or rc-aim external dcvicc and try again. |
| EFL | Fill Error | Programmed water level not reached within 10 minutes (or other programmed length of time) in any fill agitate cycle. End cycle. Power down machine to clear. |
| ESP | SPI Communications Error | Front End control cannot communicate with output board. Power down the machine, power up and try again. |
| EdL | Door Lock Error | Door docs not lock immcadiatcly upon closing (open and rcclosc door) or doesn’t unlock 5 scconds after cycle completion. Power down machine and retry. |
| Edo | Door Open Error | Control dctccts door open. Caused by pulling on door while locked or about to lock. Correct inoperative door locking system. End cycle. Power down machine to dear. |
| EUb | Unbalance Error | Unable to balance load. Redistribute load and run cycle. |
| door | Door Open Indicator | Door is not closed in Start Mode. If door is closed, check for improper wiring or faulty door switch. |
A leak error. To fix a leak, do the following: Locate damaged hoses and replace…
To fix the error, you can try the following steps: Make sure the hoses are…
When it comes to reliable home appliances, Bosch is a brand that quickly comes to…
The Bosch dishwasher, a renowned name in the realm of kitchen appliances, has earned its…
Understanding the complexities of modern appliances like the Samsung dishwasher can be a daunting task.…
Kitchen appliances such as dishwashers are vital tools that help make our lives easier. Among…