WasherErrorCodes

Whirlpool is the American brand of household appliances. It was established in the 1911. In the 1929, the company merged with Nineteen Hundred Washer Co. In the 1950, the company was named the Whirlpool Corporation.
In the 1989, the Europe Whirlpool company, which later came to belong only to Whirlpool Corporation, was created by the concerted efforts with Philips.
In its history, the Whirlpool Corporation has absorbed many other manufacturers and their brands, having strengthened its positions in the world market of household appliances.
The assortment of the Whirlpool production includes different household appliances, inter alia dishwashers.
But even the most reliable apparatus are breaking. In the case Whirlpool dishwasher not draining, refer for technical help to dishwasher repair shop Whirlpool. Whirlpool dishwasher problems can be different.
Thus for the case of whirlpool dishwasher won`t drain, a whirlpool dishwasher error codes table is presented below.
Basic Fault Codes dishwasher whirlpool
Whirlpool Generic dishwasher fault codes
Whirlpool VBL dishwasher fault codes

Basic fault codes dishwasher Whirlpool

Dishwashers manufactured by the U.S.-based multinational brand Whirlpool are well-known for their reliability and efficiency. Even the basic models that do not boast innovative features provide a choice of washing programs. There are compact and full-size models with different designs, capacity, and control panel.

FAULTS	CAUSE	SOLUTION
F1	NTC break Temperature out of the normal value (-3°C till +85°C)	1. Temperature inside higher than +85°C 2. NTC defective (the NTC is the most common cause of this error and can be obtained from this link) 3. Dishwasher is frozen, less than -3°C If the temperature is less than -3°C, fill the appliance with a cup of warm water to warm it up before you start it.
F2	Water Leakage Water is in the bottom tray	Floater or float switch switches off the water valve and the electronic switches on the drain pump until pressure sensor reports that it is empty. There are numerous causes for this fault, but it all usually comes down to the fact that something, somewhere is leaking. To cure this you need to find the leak.
F3	Dishwasher Heating System Defective Indicated after approximately 25 minutes of failure to reach operating temperature.	1. Heats too slowly (less than 1,5 °C in 10 min) 2. Water heater or heating element is defective (this is the most common cause of this issue and the heating element is available from this link) 3. Relays (RE2) on control board (CB) is defective 4. NTC - resistance fluctuation (the NTC or thermostat sensor, as noted above, can be found from this link) Check the heating element first if you get this error.
F4	Dishwasher Draining Failure Drain pump starts and after 4 min the machine detects that it is “not empty”	1. Drain pump defective 2. Siphon closed 3. Control board defective (very rare!) 4. OWl/WI defective (Optical sensors, if fitted, but most don't have them) The most common cause of this is either a blocked or defective drain pump. On that front you have two choices, you can either go with the genuine dishwasher drain pump from this link or, you can opt for a much, much cheaper compatible drain pump from this link.
F6	Water Tap Closed Water valve is switched on but flow meter sends no impulses and the water indicator is off	1. Water inlet tap closed 2. Water inlet hose blocked 3. Water inlet valve defective (common enough issue but also check the flow meter in the side chamber, the water valve is here if required) 4. Flow meter detective It is a very common issue with these dishwashers and the common flow meter is built into the side chamber which can be accessed by removing the right hand side panel (looking from the front of the dishwasher) and the commonly used spare part can be found from this link
F7	Flow Meter Failure Water inlet valve is switched on and the water indicator is on.	1. Flow meter sends too few impulses (less than 10 imp. in 10 sec.) 2. Water tap closed during water inlet 3. Water inlet hose blocked 4. Water inlet valve defective 5. Flow meter defective
F8	Water Level Failure Failures are supervised over the whole program. Mechanical water indicator WI Spray pump works, the WI switches more than 20 times in 2 minutes back	Optical Water Indicator Always after the OWI - signal is missing the electrical components are turned off for 5 sec. If after the 5 sec. the OWl-Signal is still not present then it notes a failure F8. If, however, after the 5 sec the OWl-Signal is present, then the water-level is filled to 6 Ltr. and the electrical components are again turned on. After the OWl signal is missing for a second time note an F8 failure. 1. Water inlet defect? Should switch on after approximately a 1 litre intake of water 2. Filter blocked 3. Water foaming giving false reading 4. Pot has turned off and is filled with spray water 5. No stable spray pump working, main wash motor faulty
F9	Continuous Water Inlet Water inlet valve is switched off, water indicator on, flow meter sends impulses (more than 10 imp. in 10 sec.)	1. Water inlet valve mechanically not closed 2. Triac on the control board permanently switched on. (short circuit) Reaction: interval 30 sec. drain pump on / 20 sec. drain pump off in interval The main control boards are model specific, if you want to buy one please contact us with the model number and the 12NC number from the rating plate just inside the door of the dishwasher to ensure that you get the correct one.

Whirlpool Generic dishwasher fault codes

Although dishwashers produced by the Fortune 500 corporation Whirlpool vary a lot, most of them have the same system of fault codes. A generic Whirlpool dishwasher utilizes flash lights to display an error code. To decipher the code, you need to count the number of flashes and find the corresponding information in the chart below.

FAULTS	CAUSE
F1	1 Flash NTC or thermistor open circuit
F2	2 Flashes Water leak detected
F3	3 Flashes Heating system defective
F4	4 Flashes Failure to drain out
F5	5 Flashes Rotor or spray arm blocked
F6	6 Flashes No incoming water
F7	7 Flashes Flow meter failure
F8	8 Flashes Water level fault
F9	9 Flashes Continuous water inlet
F0	10 Flashes Sensor failure, only displayed in test program
FA	11 Flashes Optical water indicator (Turbidity Sensor)
FB	12 Flashes Motorised diverter valve
FC	13 Flashes Water hardness sensor failure

Whirlpool VBL dishwasher fault codes

The Whirlpool dishwashers belonging to the VBL range vary in many respects, from capacity to design, and feature sets. What they have in common is the way the error codes are displayed in case of a minor or a major issue. The VBL models use either the “Start” LED or a sequence of light flashes repeated after a pause.

FAULTS	CAUSE	SOLUTION
F0	10 Flashes Only use in test program, indicates sensor failure	This fault code should never be visible.
F1	1 Flash NTC or thermistor open circuit	Usually it is exactly what it says and the NTC has failed.
F2	2 Flashes Water leak detected	This will be a float switch in the base normally that has been activated due to a leak of some sort.
F3	3 Flashes Heating system defective	Nine out of ten times this will be a faulty heater.
F4	4 Flashes Failure to drain out	Drain pump blocked or faulty is usually the cause of this fault code being displayed.
F6	6 Flashes No incoming water	Check the water is on and the supply is okay and then the water valve.
F7	7 Flashes Flow meter failure	This is the small flow meter fitted to the fill matrix of the dishwasher.
F8	8 Flashes Water level fault
F9	9 Flashes Continuous water inlet